Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hello! We have developed a custom board featuring an nRF9160 and an ESP32-C3-MINI-1 co-processor, which is flashed with AT-firmware (version 3.2.0.0). Our current application...
Good morning, if I wanted to develop a board with the VM3011 device, where can I find it? It seems impossible to find it as a device in major stores, and I can't even find...
Hello,
I would like to develop a temperature logger which Starts to log temperatures between certain limits
The data is stored until the device has connectivity to the...
Hello,
I know this issue has been discussed extensively in different posts, and I believe I read all of them, but still I can't get it working.
I'm trying to drive...
Hi,
I'm trying to run the i2s output sample from NRF Connect SDK 2.7.0 on the nrf52840 DK, and I'm only getting the clock signal from P1.15, and no signal from any of the...
I'm just a bit fuzzy on how all of the bootloader stuff comes together.
Our application is small (100K-ish), so a dual-bank strategy seems appropriate.
It uses a proprietary...
Hi.
Could you please tell me how to trigger an interrupt when changing the USBREGSTATUS register?
I can monitor the state of this register in polling mode, but I don't...
We used two different packages of 833 and assembled two batches of PCBs. The first batch used the aQFN package, and the radio can operate normally. The second batch used the...
Hi,
We are using nrf Connect SDK v2.0.2 with the hci_rpmsg app programmed into the network core. We have a second radio test DTM application programmed into the network...
Hi, I have used nrf5_SDK//examples/ble_peripheral/ble_app_hids_keyboard & ble_app_hids_mouse both examples with my nrf52840-DK this device is visible in my mobile and laptop...
Hi,
I have a custom nRF9160 board. ADXL362 & MX25R64 share the same SPI bus. I'm trying to validate it individually and looks like there is no communication between both...
Hi.
Board : nRF52840 DK
SDK : NCS 2.0.0 (zephyr) or SDK 17.1.0
I test qdec example.
if I set sampleper value 256us/128us, NRF_QDEC_EVENT_SAMPLERDY Event is not raised...
I am recently trying to get up and running with the nrf9160-DK and have been unable to flash the board successfully even with the Quick start (v0.2.6) app in nrf Connect....
I wanted to try getting all 3 outputs on my nRF5340DK. I tried following the instructions here - https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/security/tfm.html#manual_connection_to_virtual_com_ports_on_the_nrf5340_dk...
Hi,
We've developed a custom PCB featuring the nRF52840 Core Chip, but we're encountering significant challenges with antenna performance, resulting in poor range during...
