Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hello,
I am trying to use the peer manager on a nRF52832 acting as a peripheral with both bonding and legacy pairing on SDK 16.0.0.
The application configured with bonding...
I am using version 4.1 of the Mesh SDK and version 16.0.0 of the nRF5 SDK on Windows. I was able to successfully generate the ninja build files using CMake. However, when...
Hi,
I'm interested in multiprocol examples and I'm trying to compile examples provided by the latest sdk for nrf52840 mcu.
IAR 8.x doesn't work I have this error "code...
I have written two functions to write and read data from the flash using flash_fds module. In this way I am calling the function to write the data to flash :
fds_write_record...
Hi there,
I was comparing the power consumption of ble_app_hrs_freertos and ble_app_hrs examples on nRF52840 DK. The average VDD current is 7.4 mA for the example running...
Hello,
I'm in need of turning on and off the LTE link to use the GPS in cases where I can't depend on PSM. The LTE Link Controller library is good for this however I have...
I'm in trouble... My design has 3 SPI devices, and at a late stage I ran out of GPIO so I added a I2C I/O expander before spinning and building my PCB without thinking too...
I'm trying to use nRF sniffer 3 and can't get it to detect the dev kit on Windows or mac. I've installed it into wireshark and see the toolbar, but no interfaces are listed...
Hi,
Can we give a voltage more than VDD+0.3V on an open drain high impedance configured IO pin? By open drain, I mean:
nrf_gpio_cfg(pin_num, NRF_GPIO_PIN_DIR_OUTPUT, NRF_GPIO_PIN_INPUT_DISCONNECT...
Hello, I am trying to follow and understand the MCUboot encrypted image design found here: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/mcuboot/encrypted_images...
We are trying to connect to discovered smartphones with a Nordic 52840 chip, with S140 softdevice, discover the gatt table, read and write attributes. Most of the time it...
Hello,
I am pretty new the BLE development stuff and was mostly working on an application that works with an existing connection. But because my colleagues are not able...
I am using nrf52832 ble, I want to set the pin P0.2 low as analog input and p0.3 high as analog input .
#define AIN0 2 // analog pin p0.2
#define AIN1 3
#define AIN0_PIN_CONFIG_HIGH...
