Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
I'd like to use DFU to update the SoftDevice of an nRF52810. Based on the documentation it looks like the new soft device needs to be copied into flash while the active SoftDevice...
I got stuck drowning in all of the sdk's and softdevices..
i've recently bought EYSGJNZWY BLE chip with nRF51822 built in.
The chip comes with s120 built in, I can see...
I have two nrf52538 dev kit configured to work as peripheral(s) with simple static pass pairing program and Android phone as client. 1) peripheral_1 address = 0xCECECECECE...
I have three mesh nodes in a mesh network, a provisioner, a vendor server model, and a vendor client model.
I know that a provisioner can set client model publish address...
Hi,
we are using active voltage divider as battery readout circuit. It is controlled by MCU NRF52832 pin P0.09. Voltage from divider is read by integrated SAADC on pin P0...
Hello,
I'm working with the nRF52840 PDK and the SDK for Thread V0.11.0. The RTT Viewer shows that the program uses the Thread version OPENTHREAD/ga89eb88-dirty.
I try...
Hi,
I was trying to follow the guide to enable unit test of mesh SDK, but cannot get it through yet.
When I run the command
cmake -G Ninja -DBUILD_HOST=ON -DCMOCK_ROOT...
Hi,
I am using the nRF52 PCA10040 board. The memory settings are IROM1 - { start 0x1B000, Size 0x65000 }, IRAM1 - { Start 0x20004000, Size 0xC000 }. The board was working...
Hi，
my ble device mcu is 51822 with sdk11，when my ios app on frontend，it can search the ble advertising immediately，but when my app runs on background，it can't search the...
Hi,
I did some benchmark on internal flash access and found it takes more than 2 seconds for the device to write 16kB data. I timed by "nrf_fstorage_is_busy". Is this normal...
Hello,
I am using the sd_ble_getts_value_set() function two times in a row on two different characteristics. Both characteristics are part of the same service.
At the...
Hello,
I am really new to using the Nordic nRF51822 and I'm having problems making SPI work with the S110 SoftDevice. I was able to combine the sample codes spi_master_example...
