Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi Everyone,
i'm using ble shield with arduino mega and android app , i need to recognize the ble device disconnection ,how do i get that?
please help me as soon as...
Hi,
I am trying to transfer large amounts of data over BLE, to a large amount of devices so speed is critical.
So far, i am able to send the nRF51422 (S110 V8.0.0) a...
Hello, I looked through the forum and tried some examples but it did not work for me.
My aim is to write cccd from peripherals side (Softdevice used S110).
As the result...
Dear Nordic Team.
I have using hardware P/N PCA10028(DK Board) and PCA10031(USB dongle) for both used chip 1422. I have tired to finding FW for ble-sniffer for 1422 chip...
I am using HID example with nrf52, where firmware allows connection from proprietary HID host, e.g. PC as virtual (BLE) keyboard. When connection is established, I use button...
I am working on implementing secure DFU.
I am currently using s132_nrf52_3.1.0 (production).
I believe I have the latest nrfutil which is 2.1.0 .
When I use command...
Hi,
I am working on RTC sample example in SDK12.0.0. The compare event in it triggers after 3 seconds. In my application I want to trigger the compare event every 10 seconds...
Hi.
I'm using NRF Connect v1.0 on a Windows 10 PC, together with an nRF52-DK (PCA10040).
It works nicely with the connectivity firmware 1.0.0 that the PC app offers to flash...
Hello, I'm looking into this particular issue and are now having some concerns. Namely:
My firmware size currently stands at 30k. It's not big, but definitely not...
Hi
I set the attribute request when receive a notify
case BLE_ANCS_C_EVT_NOTIF:
m_notification_latest = p_evt->notif;
notif_print(&m_notification_latest...
Hello, we are working on a project where we use the nrf52836 with a BMX055 sensor.
Due to BLE, we have to use a softdevice.
For now, we are using this version of the sdk...
Is there such a thing? For ultra-low, harvested power, how do you recommend powering the nRF5x: load switching Vcc or leaving Vcc connected and hold the reset pin low until...
Hello,
I have got the nRF52840-PDK, and I usually use CrossWorks, so I spun up a new project based on SDK 13, examples\peripheral\blinky and flashed this using default...
I would like to connect n antennas (through RF switch) to a single nRF52 that would do phase comparison between the n received signals. This is something related to I/Q sampling...
I know it is a pretty basic question but I can't manage to understand the documentation enough to pass the tutorial predeterminate code. If someone could help and tell where...
