Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Is there a way for firmware running on the nRF52 to detect the presence of a SEGGER (or other) SWD capable device? I've looked through all the nRF registers but couldn't find...
Hi all
Our application, built on the NRF51822 Rev. 3 and the SoftDevice S130 V1.0.0, uses the UART0 with 115'200 baud, 8N1, to communicate with another controller/PC. Hardware...
Hi, In my project I want to read data from i2c and update in advertising data and the board need to advertise without time out (i.e 24x7) for these I take advertising timeout...
Hi,
I am new to the BLE profiles. I am have to send the TMP007 temperature sensor values to mobile APP using BLE HTS profile. for this I am using sample example of nrf52...
My customer offered the P/N#NRF51822-CTAA to us, I tried to find informations on it, but on your data sheet I can only find code QF, CD, CE, CF, nothing on CT. Is NRF51822...
Hi,
I have question related with some parameters of BLE transmision.
Connection interval in my project is set to 10 ms. Peripheral sends a notifications whenever the...
I have the nRF52 dev board and a stand-alone Segger J-Link (not the one that's on the dev board) connected to the nRF52 through the Debug In header.
The firmware that gets...
I'm new to the NRF5182 and I am currently working on a device where I need to wait for the tx register to send all data before i continue the flow of the program. However...
I'm trying to port your eddystone sdk to GCC. At the moment it is already compiling, but when calling softdevice_enable I get 4 as error code. If I'm right, this means NRF_ERROR_NO_MEM...
Hi,
This time I am trying to work out the UART example.
I got it to the point where it is advertising, but the advertisement is wrong.
When I check with an Android...
Hi,
I have not yet experienced well on the design and development an application using nrf51 series. Your help will be very useful for my work. My question is as following...
Hi,
I have some problems with functions sd_ble_gap_disconnect and sd_ble_gap_adv_stop.
I got critical error when i try to disconnect or stop_adv and my phone is connected...
Hello,
In our application we don't allow bonding. Therefore I'm not allowing the application to send peer data to the bootloader using dfu_app_peer_data_set()...Therefore...
