Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I would like to develop an application that makes photos using a small camera from the omnivsion series and send the data via Bluetooht, using the nRF51822. These...
Hi,
I got the error message when programming the nRF24LE1 :
"An error occurred when programming the nRF device. The infopage seem to be broken"
and also "The infopage...
Hello,
I am trying to create my own design using an SMA edge Antenna, and I am very closely following the Altium Design files provided by Nordic for PCA10005.
I have...
Hi,
I have a case where the receive end event is triggered even though the receive base address and prefix shouldn't match. Some background:
Initially the receiver is...
I am working with the nRF51822 S110 and having trouble implementing SPI. In other devices' SPI protocols, MISO can be held high until the device is ready to transmit data...
I'm uising the NRF51822 PCA100001 eval kit. I'm trying to open a couple uVision 4 projects in uVision 5. Unfortunately, it keeps telling me to install the software pack. I...
Hey,
I am designing a custom PCB with the nrf51822. I would like to use the reference layout that Nordic provides, specifically nrf51x22_qfaa. My project involves reading...
I have recently started using the new rev 3 parts with 32K of SRAM and I was wondering what the timeframe is for the softdevice to take advantage of the extra memory?
My...
I would like to understand when I would need a wired programming (with help of TC2030 connector) interface and when I would need OTA. I am trying to find the easiest and fastest...
Hi,
What is the difference between using WFE and sd_app_evt_wait to force the processor into sleep mode?
We're trying to optimize for power consumption, and somehow...
I have experimengted with prepared write on Nordic 130 softdevice and found it's quite
low performance in terms of throughput.
First, between iOS/Android device and Nordib...
Hi Nordic's experts
We got a RF problem in certification test, attached picture is the measured occupied bandwidth, the value of OBW is 1.73MHz , but the guy in the lab...
Hi,
Does anyone known what the maximum frequency is that the timers can operate on ?
I want to count a signal that is 24Mhz while the clock frequency is only 16Mhz.
So...
Hi :)
In my program, just ONE pipe to use advertising service data is not enough. There is the function:
lib_aci_open_adv_pipes(const uint8_t * const adv_service_data_pipes...
