I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
Hi all,
I am trying to "add" the DFU bootloader to my application and I have some questions regarding it:
my thought are:
add to DFU bootloader example code, part...
Hi, After compiling the at_command example form the new release v1.0.0 and updating the nRF connect tool to version 3.0.0 I get the something that looks like bad baud rate...
I am using J-Link debugger.
I am programming nrf51822. On the Jlink commander my desktop sees my J-Link Lite CortexM device.
When I try the run an example on keil5 I got...
Hi All,
I used app_uart_fifo.c and it worked however RX is not good so I switched to LIBUARTE.
The RX part is good with LIBUARTE however when TX traffic is high nrf_libuarte_async_tx...
Hi,
I am using the nrf52832 dk
i am using the uart code from the sdk.
how do i clear the rx_buf and tx_buf (buffers) and set the pointers to the beginning of the buffers...
I have read through the USBD section in the nRF52820 datasheet and I think I cannot do what I need, but wanted to confirm I am not missing something.
I would like to make...
Hi,Master:
See below:
BAT + = 3.88V
a).When I removed the MCU:BAT_ADC = 2.556V
b).When I soldered the MCU:BAT_ADC = 2.28V,Why is there a 270mv voltage drop?
In the...
Hi, nRF9160 modem firmware V1.0.0 avalable from nordicsemi.com.
"Please use nRF Connect Programmer to update modem firmware."
it means that open nrf connect and choose...
Hey there,
I am having a strange issue where once I connect to a PCA10031 device using the Bluetooth low energy app (v2.2.1) the entire screen turns white just after the...
I would like to setup a development environment for the Thingy. I see there is a User Guide geared towards demoing the example application, but there isn't a specific getting...
Hello,
Currently, I am using NRF52832 and nRF5_SDK_15.2.0. Also, I am using FreeRTOS.
I disabled softdevice by calling nrf_sdh_disable_request() before goes to sleep...
I have a custom nRF52840 board, very similar in basic design to the nRF52840 Dongle, but with a 9DOF sensor. The sensor asserts an output pin when data is ready. This output...
Hi
In the MESH_310 have LPN device.So,I want to integrating Friend feature for light_switch_server example.In this case,this light_switch_server device can be realised...
I want to measure the accuracy of the 32.768 kHz oscillator.
Is there a way to output it on a port-pin, even when it comes out via a divider?
I can't touch the crystal...
