Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Section 18.6.2 of the nRF52832 datasheet (Power-On reset) specifies the following:
A step increase in supply voltage of 300 mV or more, with rise time of 300 ms...
Hello,
I have tried the GPS sample and it worked fine. Now I want to understand the code more in detail und maybe modify the GPS settings.
But I can’t find any documentation...
Hello NRF Team,
Is it possible to change the I2S buffer size on the fly while a i2s transfer is running ? (I Am using nRf52840 with SDK15.2)
I found in the documentation...
Hi, I am evaluating the nrf52832 and the Softdevice for potential use in a new product. The product has neither display nor keyboard. It therefore makes sense to use Just...
Hello,
I am quite new to developing with the nRF52840-DK. Up to this point, I have been flashing the applications (mostly the examples) over USB with the built-in J-Link...
We need to connect 2 peripherals with single central device.I have taken ble_app_multilink_central from SDK 15.3 and integrated the ble_app_uart_c in this. I am using the...
Hello,
I want to establish an UART communication with rn2483 module with nrf52-DK, SDK 15.2.0
On nrf52-DK, pins 6 and 8 are reserved for serial port, which are connected...
Hello
I used to do TWI communication until now, but it was decided to do sensor reading with SPI communication by changing the sensor.
So that's a question,
What is...
Hello,
I am wondering that when BLE5.1 SDK will be available ?
Is there any possible ways to test your BLE direction finding solution ?
As far as I know, development...
I want to set a keep alive value of MQTT while eDRX is enabled, but it doesn't work well. Any advice?
Environment - hardware: nRF9160 DK 0.8.2 - firmware: 0.7.0-29.alpha...
Hi,
I am using nRF52832 SOC along with SDK v15.2.0 with custom hardware, currently I have requirement to use DFU protocol in BLE application to get a FW of another sub system...
Hello, I hope your day is full of the scent of flowers.
I am in the process of the Ble_Cnetral and PrePhereal project.
I have added and built the Uart.
Why is...
Hi frnds,
I am using the ble_central and ble_peripheral code (nrf52840).
i am sending 400 bytes of data to central from peripheral continuously, sometimes the boards get...
3.19 [78] TIMER: High current consumption when using timer STOP task only
I'm using app_timer_stop. But I do not know how to cope with this errata. Does the timer stop that...
