I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
Based on the ARM documentation for the Cortex-M0, the hardware can be configured to have a single cycle multiply or a 32-cycle multiply. How is the nRF51 configured?
infocenter...
For the transmission power, are we allowed to use any number in the range [-30, 4] or only the values specified in table 37 in the product specification ? When we select one...
I have a service a writeable characteristic and I'm finding the following issues.
Characteristic is read/write, not variable length, size of 4, no read or write auth, no...
I'm implementing a custom service with one characteristic and 128-bit UUID.
I am able to set the custom base UUID using sd_ble_uuid_vs_add() but the resulting bytes look...
Hi,
I would like to know can i configure advertising interval for more than 10.24 seconds.
Which are the functions i can use for configuring advertising interval.
Also...
Hi All,
Yesterday while (unsuccessfully) trying to get my dongle to work with Antware II, I did something I'm not sure what it was, but has caused the following:
MCP ...
I'm developing application on nrf51 for that i'm using...
SDK : nRF51_SDK_8.1.0_b6ed55f
Board : PCA10028
I'm trying to run code from SDK examples C:\nRF51_SDK_8.1.0_b6ed55f...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hello,
every time I try to add a new example in Keil microvision, it dont work me.
last time I try to import a new pack, I got this error:
pack instalation failled...
I use SD 7.1.0. My own app works perfectly. I use my own PCB, debugger J-Link Segger.
I try to upload any app via bootloader from SDK's example (modified in LED_pins dfu_dual_bank_ble_s110_pca10028...
I'm trying to send over a ble the data for a tablet
I'm trying to use the example of analogues (NordicSemiconductor/nrf51-ADC-examples) an old time I get error response...
Hi,
While calculating the power consumption according S110 soft device specification only ION current has been considered.
So does ION include current consumed by DCDC...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
