I'm using the nRF9160 with the LIS2DH accelerometer and SDK version 2.5.2 . In my hardware setup, INT1 is connected to GPIO 0 and INT2 to GPIO 1 . I'm configuring both interrupt...
I have a custom hardware running on nrf52840 and using ncs 2.6.1. I have implemented a custom authentication flow with customer characteristic along with the BLE bonding....
Hi ,
I am developing an application which uses nrf52833. I want to perform OTA using 4g module(from Quectel). As per my understanding and explorations, there can be two...
Hello,
I'm using two nRF9161 to communicate with each other and I want to test and measure the differences between the 3 modes available in SDK3.0.0. First, I configured...
I have tested the nRF Cloud Multi Service Sample using Quick Start and it works perfectly.
I am trying to build the sample so that I can make small modifications for an...
Hi,
I am currently using 54L15-DK to create a radio test example, but there is a problem when I build the project: - sdk version: v2.9.0 - toolchain version: v2.9.1
...
For programming the nrf52832's BLE capabilities the only option that can be used is the s132 soft device right?
According to the latest specification, the maximum throughput...
Greetings,
I have an application where the DFU of a NRF52 is performed by another microcontroller via a serial port. Once the DFU is complete, the microcontroller turns...
Hi everyone!
I'm wondering about why SoftDevice stays idle (in terms of radio operation) so "long"
("t ScanReserved" = 760 us) after channel changes during scanning? Despite...
Hi,
I'm trying to do a rough calculation of current consumption for the nRF52840 chip.
The unit should sample 6 times an hour by using I2C to acquire samples from a...
Hello,
I want to program the bare nRF52832 MCU over SWDIO, SWCLK, GND and +3,3V Connections with a Segger J-Link programmer. Unfortunately the programmer could not connect...
Hi,
We are designed our own Beacon PCB based on nRF51822 Beacon Kit...We followed board size,PCB Antenna Trace width and GND Clearance as per Beacon kit...The difference...
As I understand it only the largest physical chip, 7x7mm nrf52840 , supports Bluetooth 5.0 long range. Is this correct?
It seems as if Nordic Semiconductor is abandoning...
Hi,
i have assigned RAM address as:
#define RAM_MEMORY_TEST_ADDRESS (0x20002BD8)
uint8_t * p_ram_test = (uint8_t *)RAM_MEMORY_TEST_ADDRESS;
to this p_ram_test i...
Hi,
In the Thread API under the Command Line Interface section, there are the following functions:
void otCliConsoleInit(otInstance *aInstance, otCliConsoleOutputCallback...
Makefile (/attachment/ca6852bdad7b5e54aaa4ce4388c4c410)Please find my code attached!!!
I have changed the makefile and the SDK config file accordingly! but the error remains...
Why can not read twi data ? at nrf52832 chip....
but Read well in Arduino....
twi interfacing with RTC DS1307....
please give me some hint.....
nrf_drv_config...
i would like to print register values of an external sensor on my screen using UART! I'm reading and writing into those registers using SPI! Printing a normal message using...
Im working on 14.0 and s132 and work inside ble_uart code...i was add rtc inside that code sucsessfully but now.. when device goes to sleep so rtc interrupt handler function...
I have just changed line 74 of nrf_drv_uart.h file as
#define UART1_ENABLED 1
instead of
#define UART1_ENABLED 0
and the example gives an error. Please find...
So i am utilizing SPI and i got it to work, however for some absurd reason after removing the segger_print statement below from before the while loop the spi would stop functioning...
