Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hello comunnity,
I am trying to read, write and activite notification from my server using a central device. The problem is when I use more than 2 times, I got an error...
Hi,
Ive been having a problem connecting the phone directly through setings to the nRF51822 chip. I'm doing evertithing in mbed. When i connect the chip via the "nRF Connect...
Hello , i'm trying to implement the OTA DFU function in my custom designed board. I'm using NRF52 series. I started by flashing the flash I uploaded the softdevice132 v2 via...
I am using saadc to periodically sample a voltage (per about 12 seconds). The voltage cannot be shutdown and always is a value neigher zero nor VDD (1.25v, 2.5v, 1.0v, etc...
Hi,
I'm wondering if the DTM mode can be entered over the air interface on nRF bluetooth products, as specified by Core4.2 [Vol2 Part C] 4.7.1 Activation and Deactivation...
Hi,
I am looking for an solution which requires to have an BT dual mode(Smart Ready) SoC. As i require the high data rate of 2.1 and also require support of BLE 4.0.
...
HI ,
I need to interface particle measurement sensor with nrf52832. I am using S132 softdevice and SDK 11.0 for my application. I need to send commands to sensor to take...
Hi,
I feel myself a bit silly...my nRF52840 board was working the last few weeks nicely, it was visible both in nRFgo and Keil. I had the board some time in button cell...
Hello, after downloading my user app using keil, I can't seem to erase the whole chip.
This is what I'm trying to do:
erase the whole chip (nrf52840).
program S140...
Hello, when migrating a project from nrf51 to S140 nrf52840, I got an
"Error: L6218E: Undefined symbol app_error_fault_handler (referred from softdevice_handler.o)."
...
Hi,
I am quite a beginner about nrf51822. I understand that I can get RSSI during advertise mode before pairing. But I am not sure I can get RSSI after pairing. Can I get...
Hi, everyone.
Now I have found some posts about the development enviroment on Mac OS X. But none of them describes clearly how to setup the development enviroment with an...
We are trying to get serial bootloader (DFU) working. I compiled a debug version of the experimental_bootloader_secure_serial in SDK13.0.0 to see what really happens there...
Hello,
I am successfully using the following code:
float f = 23.50
char buffer[10];
sprintf(buffer, "Float = %f\n", f);
SEGGER_RTT_WriteString(0, buffer);
I...
