Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
Hi,
I'm using nRF5_SDK_13.0.0_04a0bfd on nRF52840.Basing on the ble_app_multilink_central example, I want to write some data to flash to save. So I use the fstorage. After...
Hello,
in SDK 11 I was using non blocking function to check if there is data to read from UART logger called: NRF_LOG_HAS_INPUT .
I can not find any function like that...
S140, nrf52840, as long as I call sd_radio_request before calling sd_ble_gap_addr_get, the program will crash and enter a default error handler, it's not the case if the sequence...
Hello.
I notice a problem with app_uart_flush function, which is calling app_fifo_flush function and in this we have a:
uint32_t app_fifo_flush(app_fifo_t * p_fifo)...
Is it possible to enter DFU / OTA from a DWT
i.e if the code crashes, and I can't trigger DFU mode by writing to a characteristic, can the WDT jump straight to the DFU...
I met this issue on some Android devices.
GATT connection is disconnected before before service discovery finished.
The issue is reporeted in following link.
github.com...
Hello, I'm using an android device to set cccd, it worked when I was running the project on nrf514xx @s110, it no longer does on nrf52840 S140, so now I wanna make sure the...
I have reformatted the code I had added earlier.
Following is the sequence of code
uart_debug_init();
gap_params_init();
services_init();
advertising_init();
conn_params_init...
NRF52832 S132 MPU6050 TWI
I want to finish the function:
When the ACC, GYRO data update, the INT pin to generate an interrupt, and then in the P026 pin configuration...
Hi,
I have the Nordic Thingy:52 (PCA20020 1.0.0 2017.19). It worked well until I downloaded new version of firmware 1.1.0 and updated Thingy. After that I didn't see advertising...
I want to use the UICR customer registers to store MAC/serialization information for my devices. It looks like the UICR customer section would be great, and the product spec...
I want to use whitelist in Central (nrf51822,SDK12),but I don't know which function to add the MAC address.
These three functions：
peer_list_get(pm_peer_id_t * p_peers...
Hi,
With S132 it is possible to advertise on specific channel.
See devzone.nordicsemi.com/.../
But, since from BLE5 advertisement can be done on any of the 40 channels...
Hardware: redbearlabs Nano V2 (see pinout below)
Programmer: DAPLink v1.5 supplied by redbear
IDE: Arduino with the redbearlab nano 2 board package
The schematic can...
I'm writing an Android application that connects to various BLE peripherals including the NRF51 and NRF52. I don't know if this question is appropriate for this site, but...
