void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi DevZone,
I am working on a project using nRF52840 preview DK and Arduino CAN Bus shield. I modified source code base on some Git Projects. It seems the SPI initialization...
Hi everyone!
I want to implement SPI with "ble_app_beacon" example with the following hw/sw.
DK : nrf52832
SDK : nRF5_SDK_14.2.0_17b948a
IDE : Segger Studio 3.34...
Recently,I use the SDK14 to develop the project,the initial project is in the content "SDK14/examples/peripheral/twi_scanner/pca10056",
Then and the spi example in the content...
I have build the light switch demo, it works properly. But I want to make multiple sensor node that takes data from sensor and send to single relay node. I am little confused...
I just integrated CMock which is part of my unit testing framework and i am trying to test a mocked function however i am running into RAM overflow error. Is there a way to...
May need to post this question to Segger, but I'd figure I'd ask here.
Have a nRF52832 project that compiles, links, and runs fine on the 52832/10040 dev kit board.
...
Hi All,
I am using the nrf52840 to run an application which does not use the BLE.
I need to add firmware update capability to the device so that I can push updated in...
Hi, I am running into a connection problem with connecting to the Secure bootloader example in SDK v13.1, whenever I try to connect I get Gatt 133 error. To my memory, the...
hi,
i doing a project where i have combined light switch server from nrf_mesh sdk 1.0.0 with nrf5 sdk 14.2.0 ble_uart_example to send.
my aim is to send on_off command...
We currently have an application that is running SDK 12.1 on the NRF52832. We have no issues doing a firmware update using the iOS SDK. What we are seeing is a long delay...
Hello, I am running bluetooth example.
I am using the nRF52832 board and SDK 14.0.
I modified the multilink example to make a slight modification and connect it to another...
I have a windows side application and an Android App, both of which are set to capture data from the Thingy Sound Service.
On the windows application, the data after being...
I need to be able to reserve some flash to permanently store manufacturing values that will never change. I did this on an nRF51 by reserving a 4KB block and setting the necessary...
Hi all ,
I have problem . I have 1 NRF52832 dev kit . It connect to STM32 devkit via UART . I want to tranfer firmware of STM32 from smartphone to NRF via BLE , and from...
Hi,
I added this in SystemInit() (just below the CONFIG_NFCT_PINS_AS_GPIOS section) within system_nrf.c so that I could easily turn on or off the APPROTECT read back protection...