Hello everyone,
We are developing products with nrf52840 and our default supply voltage is 1.8V.
Is it possible to program a custom 1.8V board with nRF52840DK?
We are...
Hi
I am using nRF52840 with SDK 15.3.
I have a project where I uses FatFS to write to a SD-card with SPI interface (SPIM3). This works very well.
I am now trying to...
Hi everyone,
I'm currently following the "WiFi Fundamentals" course provided by Nordic, and I'm encountering issues with this specific exercise (l5_e2):
To ensure I wasn...
Hey so I just wanted to use the BMI270 on the Thingy:53 and Polling the acceleration values seems to be working just fine. I wanted to use the DATA_READY Trigger. I am working...
Hi everyone,
In nRF9160 with ncs 2.9.0 I've problems when trying publish a MQTT payload bigger than 2700 bytes aproximately. In advanced I already was adequated buffer size...
Hi, I've recently acquired an nRF54L15DK, and started the development on BLE, I'm fairly new to Nordic's enviroment. In the last couple days I've been trying to build the...
Hi everyone,
I use the ble-app-buttonless-dfu example to develop my application.
I make a mutual authentication to be sure the device is connected to the right mobile...
Hi
So far I have been using the examples from Keil 5 pack installer.
Now I tried loading some from the SDK example folder and I have issues with includes.
What do I need...
I included button less DFU service in the proximity profile example.When i compile i am getting the following error.
..\..\..\..\..\..\components\libraries\bootloader\dfu...
Hello,
I am working with the example "experimental ble app cgms" in SDK 13.0 and using nRF52832 DK.
when a connection was settup and pairing completed, the CGMS sensor...
I want to ask general question about antenna designing as I am designing antenna to be used with NRF52.
The picture attached with this message shows a printed antenna coil...
At the moment I'm sending a notificaties during the BLE_GAP_EVT_CONNECTED event. This sometimes results in various errors but I can take care of those. The issue I'm having...
GerberVINR-178.zip
SchematicVINR-178.pdf
Bottom layer
Top Layer
IC on the PCB is marked as follows: nrf51822 QFAAHO 1627WM.
I am able to program the custom...
Hello,
I want to create BLE connection between two different modules - nrf51822 and TI CC2564 (possibly Laird BT800). Is there any chance on using Gazell protocol on other...
Hi,
if I got it right, the Radio Timeslot API is not supported by the S140 softdevice. Is this right? Why is this and are there any plans to support the API in later versions...
HI, every one, I joined the watchdog program in application,i use sdk11.0, and i found the problem that when i download the program , the MDK compiler point out "error: flash...
Hi,
I am doing development on Android platform. I am using Marshmallow device to develop my BLE application. Many times I am getting status code 129 in onServicesDiscovered...
Hi, i'm working on a custom board with microswitch (Crouzet V4) in order to get the position of a moving part inside a machine. This switch is in pullup mode with a 100k resistor...
Hello,
I am using nrf51 and sdk12.2. I want to print data to terminal using printf function. So I added app_uart_fifo.c also I included paths. I did not get any errors from...
I'm using NRF51422, s130, SDK v12.
And I'm working on a project that can connect concurrent peripheral and Central.
In this continuious connect and disconnect sequences...
Hello,
I am using the bootloader_secure-Example on a custom-board and I want to configure a LED as status-indication.
Since I am on a custom-board I disabled the functions...