Hello,
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board (provisioning and configuring inside the software and not through external app...
Hi there,
I am trying to interface at25xe321d with QSPI but it always end up returning zeros. Please find attached code and dts file for reference. Thanks Moh
Hi,
We have a custom PCB based on the nRF9151 and nRF7002 for a tracking use case, supporting both indoor (Wi-Fi scanning) and outdoor (GPS) positioning. Our firmware is...
When version 1.0.0 of nRF54L15-DK evaluation kit will be available and how to distinguish the version when ordered from distributors like Digikey?
In discussion here:
...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
Hi,
I need something that can be the Master and talk to the Evaluation Kit Board to try to send a large amount of data. Do the Master Control Panel, or the mobile app nRF...
Hi,
I am using the nRF6310 + PCA10005 +nRFgo Studio as the lower tester, the supplied python scripts as the upper tester, and my own custom board as the DUT.
I've looked...
Hello, I am working with nrf51822 on my pcb design by myself, I read temperature from chip, the result is about 90deg, (I have div by 4 for 0.25 deg) it is impossible for...
Is there a way I can tell which version of the chip I'll get from a distributor? It's not clear to me that I can tell, from, eg the Mouser product page which rev it is. Is...
Hi,
I am working on proximity android application, i implemented immediate alert service, which is working fine. Now i need to set the alert level on the tag for linkloss...
Hi
I am working with alert notification example. I just wanted to know how you have tested the alert notification client example implementation. Is it just by using the...
Section 28.9.9 of the nrf51 reference manual shows the Config register has 3 defined bits, BBA. A is for Hardware Flow Control and is one bit, 0 or 1, which makes sense. ...
Hi,
I'm trying to add more user services to LBS demo. I generated 128b UUIDs for my services. Then I should add them to list returned by scan response in function advertising_init...
Hello!
Sorry for a new guy's description.
We had a device running in normal firmware application mode, and the Bootloader was programed. It's our goal to accomplish DFU...
Hello
I am using the nRF8002 kit. I would like to inform the host (Android app) when there is a long button press on the input pin.
Is this possible and if so which BLE...
Hi folks,
I was wondering if someone has a reference implementation of a bootloader that uses exclusively ANT technology to make DFUs, being it ANT-FS or any other alternative...
Dear Nordic guy,I'm developing with nrf51822 (6.0 stack binary and 5.0 SDK).
I recently updated the code and stack binary(6.0 stack binary and 5.0 SDK).
My function is not...
This is something for the legal department.
You had some questions here about the RFduino before. This question is about legal obligations Nordic supposedly imposed on...
Is it possible to use an nRF8001 without a separate microcontroller to advertise non-connectable advertising packets specifically containing battery level information only...
I take the nRF UART 2.0 for reference. I make the nrf51822 be always sending packages ,and if it sends one package succussfully,and the smartphone just shows what it receives...
