void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi,
I have 2 nRF512840 eval kits and tried out the att_mtu_throughput example provided on SDK 13.0.
The throughput about 900-1000Kbps can be achieved with PHY 2.0 DLE...
Is there any way that I can use more than 4 timer in nRF 51 ??
(four or more...)
I'm using Softdevice 130, so It uses Timer 0,
and I'm using RGB Sensor using PWM Library...
i m new in NRF52832, i use saadc exemple pca 10040 sdk 13.0.0, i dont now how to get adc result from the buffer because there is 2 elements in the buffer :
err_code = nrf_drv_saadc_buffer_convert...
Hi, Nordic Forum!
We've been trying to implement an adapted version of the Secure Bootloader with Buttonless DFU in our custom board. We have successfully accomplished...
In this app by Nordic
github.com/.../Bluefruit_LE_Connect_Android
a cyclic redundancy check (CRC) is added to the payload byte array before writing it to the UART receiving...
i am creating a user interface using the sh1106 driver for a 128x64 pixel oled screen. so every screen is a list of items to be scrolled; however almost every screen i am...
Hello,
i'm currently researching the possibility of building scatternets with BLE. As the S130 softdevice supports multiple concurrent roles, it seems very possible (see...
Hi,
I'm using s140_nrf52840_5.0.0-2 and there are two characteristic for the peripheral, notification and indication. When I use notification to send data, I will get the...
Hello,
Are there examples of AES CCM encryption/decription?
Is there a recommended procedure for generating nounces?
Are there recommended procedures for using CCM...
Hi,
I have camera interfaced on GPIOs of nRF52832.. I am reading image data at the rate 80KHz.
Is it possible to write the data to SPI Flash (Slave) by DMA or by any other...
Hello,
I am using pca10028 and sdk 12.2. I am trying to add app_uart_fifo.c file to my code.
I have added the paths and also I have made changes in sdk_config.h. The changes...
Hello,
I am using nrf51822 / sdk10.0.0 / S110.
I write flash in SD / bootloader / application order.
I use nRFgoStudio and J-Link.
There are about 20% of malfunctioning...
SDK10 examples work when built for s110.
When building the same for s130, they do not run.
Debugger indicates main() is not reached.
Tried both Keil and armgcc.
SDK12...
hi,
how to send and receive data using UART0 without interrupt request with softdevice s110.
i tried to disable interrupt it could not give any response.
please help...
