here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hello,
There have been some questions on the forum regarding the DFU and it's zero value for the application CRC. However, none of them seem to address this question so...
Regarding the radio peripheral, I stumbled upon these 2 properties and have no idea what they are for.
What's access address? And what is a channel? Shouldn't there be...
I am runing ble_connectivity example with simple_uart instead of app_uart was not working unable to scan not getting advertisement reports.
Its been working with PCA10001...
Hi,
I have a pretty simple problem but I can't get it right. This is what I want to do:
T=000, PIN_x = 0
T=004, PIN_x = 1
T=100, call a routine
T=543, Start over...
Hi,
In the BLE_UART example code posted here , I noticed a discrepancy with the SD 3.0 migration document, SDK12, and the example code.
In stock SDK 12.1.0, ble_stack_handler_types...
Hello everyone, i need some help and suggestions in understanding what is exactly happening. I have read a lot about bugs and workarounds in pstorage and now i actually don...
Hi, when reading radio transmitter peripheral example, I got stuck a bit on radio_configure(). I got stuck because I can only get some brief from the corresponding .h file...
i m using nrf51.... first i have call WFI(); and device goes to sleep mode...and when press any switch on gpio so, wack-up again...so, may i know that.. how many way for wack...
i m using gcc toochain setup in windows for pca10028 devlopment kit... and load BLE_UART code inside it... and now i m add onother rtc code inside it.. but it's not work....
main.c hello sir.. i m place rtc example code inside of ble_uart code .. and i m using gcc tool chain setup for pca10028 bord... code complile sucsessfully... code not work...
Hello all,
I want to use a single bank bootloader with the ISP1302 Module (nRF51822 Chip) and S110 (V8) Soft Device, SDK 10, for application update
Can I use the BLE...
when i use nrfjprog.exe download my application code,Change nrfjprog.exe --eraseall --program ble_module.hex --verify --reset to nrfjprog.exe --eraseall --program ble_module...
My apologies, but I just want someone to give me a quick brief on what are these things and how they work. AFAIK, the nrf51xxx series SoCs render limited, sporatic radio availability...
Hi,
I am Working on a BLE application in which I do not want to expose certain services until I am securely paired/bonded to a valid device. The problem is that during...
Hi,
I'm trying to use sd_ble_gattc_characteristics_discover to figure out which characteristics are in a service.
On the whole it seems pretty obvious (keep calling...
