I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
How does the nRF8001 chip generate the passkey in the DisplayKeyEvent? Is it possible to set this passkey from the App Controller?
As I understand it, the SetKey command...
I find this strange but I can program the HRM demo fine but with my own code it compiles with no errors or warnings but will not program with Error: Flash Download failed...
Hi Nordic,
I want to develop a PC software that works as a master device which can scan for advertising packet, establish connection, etc. Basically, something similar...
Dear Sir,
After I remark this //BLE_GAP_CONN_SEC_MODE_SET_OPEN(&cccd_md.write_perm); and program it into nRF51822, then I cannot program it again. PC program report it...
I have modified the included HID mouse example to allow for left/right/middle mouse clicks. However, it is not clear to me how to set an event handler for both when a button...
What is the recommended PCB thickness of the nRF51822-QFAA Reference Layout? It'd be great to have a specification in the package including the full spec of the PCB material...
Hello Folks, I'm starting some work with the nRF51822 Evaluation Kit (PCA10001), but have very quickly run into a blocker when trying one of the ble samples. (I've previously...
With Soft Device 5.1.0 I generated the binaries from the hex by doing:
arm-none-eabi-objcopy -Iihex -Obinary --remove-section .sec1 --remove-section .sec2 s110_nrf51822_5...
Dear support,
We are in the design stage for a BLE application. We looked at different options. Although the NRF51822 seems better in specs. The TI parts CCxx offer this...
So far I have made a successful program that utilizes BLE to send and receive radio signals in Kiel. But I have only been testing this program by using the provided Master...
I just entered a Case to Nordic with this same question but do not expect to get a response over the weekend so I am posting here. I made the assumption that the Nordic Cases...
Dear everyone:
Now,I have a project which use Nordic product solution to developemnt.
And , We need your company to provide some information and solution.
(like,have...
What is the maximum value of RSSI parameter for nrf_gzll_device_tx_info_t structure?
I have done a test on RSSI parameter value return in nrf_gzll_device_tx_success callback...
Hi Nordic
I don't fully understand the drive settings for the GPIO. For example S0H1 means when the pin is CLEARED, it will use standard drive (can sink 0.5mA) and when...
