Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello,
I'm using low power comparator with cross detection.
It works but I can't detect if it's failling or rising edge.
Can we detect simultaneously DOWN and UP...
Hi,Everyone! Now i have the board nrf52832 and i'm trying to get the battery value and send by using saadc.
i have read the example of ble_app_proximity and saadc,and i configure...
Hello! I compiled hex file with NRF52_BOOT in mbed cli. It was programmed successfully. Mbed os version include fix to use nrf52 DFUService. Bootloader is loading correctly...
Hi Nordic guys,
we are observing a strange behavior. Here some background on the project:
we are developing a peripheral device that asks via L2CAP signalling connection...
Hi,
I would like to know, whether it is possible to use a TCXO with single output as a LFCLK source, i.e. connecting the TCXO output only to XL1, instead of connecting an...
Hello everyone, I encounter a question. I follow below link to solve the issue.
https://devzone.nordicsemi.com/question/104118/adding-pwm-to-ble_template/
I've set the...
We are currently porting our proprietary stack from the nRF51 to the nRF52.
To save on BOM we are using an external 20ppm 32Mhz crystal to synthesize a 32Khz clock (power...
Hello,
I have develop an android application which connects to BLE device and perform read and write operation, so for this i was using Android-nRF-UART .
But my application...
In the release notes for the IOT SDK (which as the MQTT examples) it says: "Once BLE link is disconnected, lwIP example applications no longer get a global prefix. The only...
Hello all,
I am new to ARM architecture with some prior experience in Arduino based application development and some FPGA experience. I have a few queries:
Should...
I'm developing a project based on the Nordik UART Service and I wouldn't use pairing as in the example.
However I have some problem when a central device is already connected...
We're targetting the nRF51822 and use the pc-ble-driver (via connectivity_1.1.0_115k2_with_s130_2.0.1 )
Currently I'm using the dev board and the virtual COM port connection...
Hello,
I am trying to move from ARM Compiler v5.06 to v6.4, but I encounter an error, which I cannot handle.
The project builds fine with v5.06. When changing to v6...
Hi;
I am trying to secure DFU OTA. For that, i am using SDK12.2.0 and done with example file.
Now how to generate this .dat file itself.
Also explain each parameter...
