Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hi,
I use a mcu nRF52840 on a personal card for a project and we are stuck on interruptions: hardware pin and timer. I use the lib "nrfx" for future accounting purposes...
Using NRF_SDH_BLE_OBSERVER in a non-static context doesn't work because the registered variable, and therefore the handler context is lost. How can one register for ble events...
Dear,
I am using nrf9160 DK, we can download hex fiel for boardcontroller
nRF9160 DK board controller firmware
https://www.nordicsemi.com/Software-and-Tools/Development...
Based on the experimental_lpn example if have ported at application (light switch) to work as a low power node.
Everything work fine on the lpn node where i use the generic_onoff_client...
Hello,
I tried to update bootloader on the dongle via DFU, but It failed.
The dongle uses OpenBootloader, so it does not check signature for firmware packages. But the...
Hello,
I'm working on a project where we are doing the following:
Collecting sensor data and storing it in an external SPI flash
Retrieving that sensor data from the...
Hi,
When publishing a message with access_model_publish() the p_message->p_buffer must be remain valid until all retransmissions have completed for loopback message but...
Hello
I want to modify the tx powel level to 4 dbm using sd_ble_gap_tx_power_set(BLE_GAP_TX_POWER_ROLE_ADV, m_adv_handle, 4); after Advertising_Init function.
I could...
Testing with the NRF52840 dongle and the Power Profiler Kit. I see a reading of ~5uA when sleeping without SAADC enabled.
I use this code to enable SAADC
My power...
Environment
- DK 0.8.2 in which SB44 is cut, and P1 and P2 are connected - firmware v1.0.0 - program : asset_tracker - SIM: iBasis
Before updating firmware, asset_tracker...
Hello. Got such a problem. I use nrf52832 Adafruit Feather board. While working with BLE examples (Softdevice and app.), debug via serial works fine. Can see all the text...
Hi,
I have a desig where the space is minimal and I have one nRF52838 and one nRF52840 microcontroller. Is it possible to place them at the same coorinates, but on oposite...
Hello everyone and Good day
I am a fresh graduate and its my first assignment at my job. I have to flash an LED at 1 Hz using NRF52810 BT 5 chip.
There are so many development...
