Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
dear nordic employee:
I tried to download the project of the ble_app_hrs_c_central by keil(nrf52832)
but It show like the title
I know I should reset the IROM1 and...
Is there a way to get the supervision timeout counter from the peripheral side? I am currently working with nRF5X modules and starting with the nordic uart example from the...
I'm using nRF52832, soft device 2.0, SDK11 and as a central.
When it happens I'm scanning for peripheral to connect. Usually it's a peripheral advertises at very low rate...
Hello,
I'd like to work with my nrf52832 DK while traveling(sins I do that alot recently) and would like to download somehow all of the pages in nordic's info centre to...
It's clear an Android device can be a central, but I'm having a hard time finding any information indicating an Android device cab be a peripheral that an NRF52 could be programmed...
Our products should connect to a central device. This central device should also be a peripheral which a phone can connect to. Will this be possible? If not, could the phone...
Hi, I need some guidance or an more in-depth example on adding the necessary code to read/write on the UART1 using the serial module or something else. Everything I've tried...
I am working with nRFx modules and have a few questions about updating parameters. I started my project with an example and modified what I needed. However, I am not sure...
We create library for work with software serial, we use two modules gpiote, timer.
We have done software serial one instance but we need four (actually just for rx). We don...
HI,
I am using nRF51822 S130, SDK12.3.0
I created private key for application code and public key for bootloader. Just few days ago, the zip file can upload to the device...
Hi,
I use NRF51822 + S130 + SDK12 platform, my device work in CENTRAL mode, I want send data to peripheral every 10ms, code like this:
while (1)
{
while (m_free_tx_packet_count...
Hello,
I am currently working on nRF52840PDK baesd project, where I want to use BLE using RIOT OS. So, please can you provide any example for RIOT OS based BLE or any details...
Hello all ,
I am using nRf52832 and i found PWM conflicts with Softdevice: We were able to create a sample PWM application which works fine independently. When we merge...
I'm developing a system which consists of 1 or more remotes (3 or 4 max) that have to communicate with a single host.
I need a fairly simple protocol, low power optimised...
hello all,
I am using nRF52832 and blow is my querry.
Implementation of power ON/Off feature:We are able to put the board to system ON low power and System OFF low...
