Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
I am not sure where to post this info so I do it here. We have been testing nRF51822 chips in a Rigado BMD-200 module powered by a single 2032 battery and have been getting...
I am using the minimal port referenced in this question: devzone.nordicsemi.com/.../
to interface the nRF8001 using an MSP430 device. I am currently in the process of porting...
I am using SPI MASTER example from sdk 7.2.0 with softdevice s110(using spi along with BLE).
In my program I have a requirement of reconfiguring spi pins after using spi...
I see that driver version 1.0.0 was tagged on ghitub: github.com/.../v1.0.0
However, when I visit this page: www.nordicsemi.com/.../38649 , I can only find the 0.5.0 version...
Hi
I use nRF51422 for our products.
In a product line, we check the CWtest mode current consumption current.
I decided the determination value of the CWtest mode current...
Hi.
I'm using nRF51822, S130, SDK10.0.0.
I made a source code as below refering radio_test which is in SDK examples.
But the width of frequency is just 0.2MHz as below...
hi,
so i was coding my program with keil and it reach the 32kb so i had to move to the free IDE Eclipse. for that i followed this tutorial devzone.nordicsemi.com/.../
...
Hi !
I've seen that the Makefile given with the examples changed a lot between SDK11 and SDK12, lots of improvements ! However there's still something I don't get. Why...
What system resources are required when using GPIOTE channels (not the PORT event, the other channels)?
I remember on the nrf51822 there was a long-running PAN, fixed in...
I programmed nRF51822 with S120 softdevice and ble_app_hrs_c application to scan beacons.
It works fine but have one problem.
It scans beacons for about 10 seconds...
hi,
i am working on ble_app_uart_simple_adc example which is referred from the link github.com/.../nrf51-ADC-examples
i flashed the code successfully. and detecting the...
Running the SDK11 example \examples\peripheral\twi_sensor on a NRF52 PCA10040 version dev board and can't get any output from TWI pins. Leaving pins unconnected and using...
Hi,
I am trying to set up the development tools for the NRF52 on my Mac by following this tutorial aaroneiche.com/.../
I am getting the following error when i try to...
Hi
I want to get external acceleration sensor values with SPIM using easyDMA on the sensor interruption (using GPIOTE). then after getting all data, I want to calculate...
