Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Im' trying to send a set of 80 bytes using indication. for that I have a characteristic sending each time 20 bytes and wait for indication acknowledgement before sending the...
Hello Nordic! My application requires an nRF51822 using S110 to handle both Notifications and Indications over the same characteristic.
The CCCD value 0x01 = 0b01 enables...
Hi,
In order to start my own board with nRF52 component throught SWD, I think I've to use Segger Jlink. I expect to buy the basic version, that sound good for me, but I...
Hi,
I have some problems with bootloader debugging by using app_trace_log().
My board is pca10028, and I use the SDK 10.0.0 for it. The Keil version is v5.20 and Jlink...
Hello All,
How to interface nRF905 with nRF51DK board?
Any driver is available for nRF905 which support nRF51.
Any help will be appreciated.
Regards,
Rajneesh
Hi,
I'm using PCA10028 to communicate with ADS1131 ( www.ti.com/.../ADS1131) which outputs 18bit on SPI bus. I managed to get the data out by reading 24bits, but it feels...
Hello ! When I make a read with the SPI from a sensor's register the data sometimes comes correct and most of the time wrong. I tested the read operation with an Arduino and...
Hi
what is the best way to implement a sleep after disconnect?
We are using a custom board and I implemented it this way:
on connect : turn advertisement off
on disconnect...
I used iar for my project. But for some reason I have to transfer my project to keil now. Attached is the icf file from iar and I also attached my keil settings. Now the system...
In following the example for a DFU BLE upgrade I have configured the following system
on an nRF52 DK install the softdevice and bootloader:
nrfjprog --family nRF52...
In my code, I have some 'print'-style functions that write data to a buffer, and that buffer then goes to the Nordic UART implementation. This is user code, and I don't know...
Hi, I'm trying to adapt the stm32f4 library from:
link text
to run an nrf24l01+ with an stm32f373. After some initial SPI headaches, a lot is working. In the initialisation...
I want to confirm how much current is being drawn from the battery while the nRF52 is in it's absolute lowest power state and waiting for an NFC field to wake it up. From...
I am interested in setting the tx power level the advertising packets in a nRF52832 are transmitted with. I saw there is the TXPOWER register in the RADIO section (address...
