Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi,
So i'm working on an android app that communicates with two nrf51822 devices on the s110 softdevice by switching between them continuously (connecting one, disconnecting...
Hi,
I am using an nRF52840 Dongle with an external debugger and an external UART, provided by a USB to UART adapter, its an FTDI board.
I have modified my overlay file...
Sir,
How can i use the SCAN REQUEST to transmit dynamic data PDU to the PERIPHERALS ?
The idea is that the CENTRAL sends data to PERIPHERAL without make a connection!...
I am using the fatfs example in SDK 15.3 and I need to implement an energy saving mode for a use case when the sd-card is inserted but not needed. In a first step I'm cutting...
Hello, first of all I am new to Zigbee.
I have read the Light bulb example, and now wondering on connecting it with some kind of power consumption monitor. I want to create...
I have been using UART0 to implement a very simple console using console_getline_init() and console_getline().
So the nRF5340 receives commands over UART0 and outputs printf...
We're building a cryptocurrency hardware wallet. And we're using the secure bootloader provided by nrf5 SDK, to only upload signed firmwares to the device. We are using nodejs...
Hi guys,
I am working with nRF52832 board and Zephyr for a short period of time and I really don't have to much experience. Every day I learn some new things and try to...
Hello,
We have a custom board of nRF52832 with two buttons and right now Buttonless DFU is also working perfectly. But, we have scenario where if combination of two buttons...
Please help with writing to flash. If SoftDevice is off all ok. If SoftDevice is enabled, the sd_evt_get function always returns the value 5.
Here is the test code:
Hi!
We are developing a tracker based on Thingy91 using GPS and LTE. We're using the latest Modem firmware 1.2 and Zephyr/NCS v1.2.0
The GPS cold start until receiving...
Hi Devzone!
I'm trying to monitor the battery level of Lithium Ion battery.
I'm using SAADC to check the voltage of 3.7v 3500mAh Lithium Ion battery.
The battery...
when I am waiting for an event the current consumption is becoming ~180uA continuously.
I am waiting for an event using the following function
void deep_sleep(void) {...
Hi All,
I would know, is the NRF52 BLE Mesh Bluetooth 5.0 qualified or not. I did not find it anywhere. As I can see the in Cypress website, they clearly mentioned that...
