I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
i am compiling an code just to store a data to flash and retrieve it. i wrote the code for that i included fstorage.h,section_vars.h and added fstorage.c. I am not using any...
Hi,
In nRF5 SDK v14, in the file ble_advdata.h, there is a routine to create advertisement data from a ble_advdata_t struct that is passed. This struct allows only 1 manufacturer...
This omission leads to linker errors:
_build/app/nrf_ble_gatts_c.c.o: In function `nrf_ble_gatts_c_on_db_disc_evt':
nRF5_SDK/components/ble/ble_services/experimental_gatts_c...
Hi All,
We are working on nRF52832 custom PCB design. We are having a small concern for shielding. Do we need to provide shielding for nRF52832 based boards for FCC certification...
Hello,
I am trying to understand a bit better BLE throughtput in order to use it for my application, having read this Nordic Blog , this post and ATT_MTU Throughput Example...
Hi!
I have adapted the heart rate example to have just one service and one characteristic. Initializing works fine and I can read the initial value of 0x00 using my cell...
Hi all,
i have a question about the communication client and server.
I'm using for my project a nrf52 and softdevice s132 v2.0.0, reading the datasheet i can understood...
Hello
we have a projekt with periperal "ble-app-blinky" und central "ble_app_blinky_c".
how to do:
when the "peripheral" battery is below 2.3V
then the led 4 on "central...
I'm trying to regularly change some advertising parameters ( ble_gap_adv_params_t.type ). The only way i can see to do so, is by stopping and starting advertising.
However...
I made a pulse oximeter product with nrf51822AC(base on SDK5.2.0 & S110 6.0.0), and implemented SIG GATT-based profile（PLXP+PLXS). Now we want to do BQB RF PHY testing to...
I have an example combining BLE, UART and SPI in which I use RTT to watch the startup process.
The SoC is nRF52 (BLE Nano2); building with armgcc.
This works ok when JLink...
Hi,
I need to send large data(about 200KB) from android phone to my custom board.
Connected like this :
Android Phone ->(BLE) -> nRF51822 ->(UART) -> Custom board...
Hey everyone,
I'm new to the Nordic/Thingy/Embedded world and was hoping I could get some hand holding to achieve a simple change.
I would like to change the Thingy...
Hi All,
I am working printer project where i will be using two boards , one is nrf51 dongle which acts as client(sends/advertise the data) and another is nrf51422 soc on...
Hello community,
I did a central device which is connecting with 8 slaves and this slaves are sending every time 8 bytes when they are connected. My set up is the following...
