I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hello everyone,
I am going to run the serial DFU example. I follow the instruction on infocenter website and run the example by using my own keys and image and I got this...
Hello everyone! I'm creating BLE HID controller, where high packet rate is important. I expect about 100 packets per second. But when I try to launch hid mouse or hid keyboard...
Hi,
I am using NRF52832 based module. What is the maximum no of notifications we can send per sec. Is there any limit.
I am facing a issues on increasing the distance...
Hi Guys. I see that yesterday Nordic announced the nRF5340DK touting LE Audio. Is there a SOURCE and SINK example that even preliminarily demonstrates this capability on the...
plan to build a bluetooth to Nbiot edge gateway module and select nRF52832. Build the module to combine the nRF52832+BG96(Quectel)+multiple sensors include BME280,LIS3DH,LIS2MDL...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi,
I have a problem with nrf5340pdk not executing the firmware. I have to build a hello_world sample from ncs v1.4.99-dev1 and I flash the development kit with the west...
I'm considering rolling back to the sdk ver 14 to avoid the nrfx vs legacy api confusion.
I plan to use only the 52810 and 52832 SoCs.
Is there any disadvantage to using...
Hi @Vidar Berg
Hope you are doing well ! i need your help regarding the beacon coded phy . I read your post
https://devzone.nordicsemi.com/f/nordic-q-a/69595/problem-with...
Hello.
Trying to compile the AES CBC MAC example out of the box, we get the ferror below.
Your help would be appreciated.
Many thanks,
Andrew
Building ‘nrf_crypto_aes_cbc_mac_pca10040...
Hello,
Updating developer machines to OSX Big Sur resulted in nrfutil failing to execute. The install via pip works correctly, but when attempting to run the binary, the...
Hi All,
We have tested the DFU(nrf52840) from a central to the target device over the BLE. In which a central device attached to the PC(x86-64bit Linux) via a Serial USB...
Hi Folks,
I am facing an issue while trying to perform a system On suspend procedure with a wake up on HITOLOW event.
No event is triggered when button pressed.
However...
I wish to develop a bare metal application (without Zephyr) on the nRF5340.
For this purpose I am unable to find the documentation how to perform Inter Processor Communication...
