I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
In the Light Switching example the Health model is used, but is it mandatory to used this model for Bluetooth Mesh applications or I can choose not to use it if i don't deem...
Hi everyone,
We're using our own customized BLE service with nrf51 on the one side and Android Smartphone on the other.
While connecting to the GATT I'm getting Error...
Forgive me if this is a stupid question, but I am new to programming microcontrollers other than Arduino and SPI in general.
I have a DAC that has a 16-bit register and...
Hello,
I am using 10 bit ADC read VDD voltage convert into mv without using any external voltage divider circuit, as per following function:
static void adc_configure_battery...
I'm embarrassed to say that the loopback I2S example, while able to show me that data can be sent and received through I2S, wasn't enough to help me achieve a simple demonstration...
Hi:
I am using SDK14.0 S132 for nrf52832 , i found it's sleep mode power comsumption large than 5mA .
I am using internal LDO and external power is 3.7V li-battery cross...
Hi
Just to be sure: I've recently bought the nRF52840 Preview DK (dev board for nRF52840) but I think I'm going to use the nRF52832 instead for my project.
Is it ok to...
Hi i want to create a new project in Eclipse. I did this my following the complete code form git hub for devzone.nordicsemi.com/.../
*Nordic has provided sample code for...
Hi!
I've based a new project for the nRF52840/S140/Preview-DK on ble_central/ble_app_uart_c .
I use the NRF_LOG_XXXX macros for debug and they print fine in RTT Viewer...
Hi,
I have two nrf51822 device, on work as GAP Central, another work as GAP Peripheral.The two device use different connection parameters, after the connection is established...
hello,
i have developed one board using nRF52832-QFAA and trying to dump simple LED blinking code in it using nRF52 DK board. But code is always dumping into custom board...
How do you do
Now need pwm_driver demo5 duty ratio, is there any way to 1/6 or 1/8?PWM and phase difference is 4 road？
Ask for a few days, change seq_values [], but how...
I am developing firmware using S132 (SDK 11) for a custom board.
After performing Pstorage Update, if I do not wait for the callback from pstorage before continuing execution...
