I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
May I ask you a question? concerning I disable the radio of nRF51822 2.4GHZ ， don't run the Ble，don't apply the the RC Oscillator of the 16MHZ and only use GPIO，could the...
hi,
I test the gazell example gzll_ack_payload in SDK9.0,I found that the default timeslot period is 600us.But after testing using logic analysis,I found sometime transfer...
We are intensively using nRF2401A transceiver. Due to the fact that it's now not recommended for new desings, we are about to migrate to nRF24L01+
The problem is that we...
I have been using SDK 11.0.0 in a gcc/Eclipse environment successfully.
I can download the ble_app_hrs_pca10040_s132 example to the dev board and successfully run the HRS...
I am developing a script that runs on the nRF51822/ BLE nano to connect to other devices using blue tooth low energy. To do this currently I am looking at the heart rate example...
I am testing the ble_app_uart and nRF UART app. When I transmit the message from mobile phone to the module. The module can always receive the data and display on the terminal...
Here's the original error:
compiling app_util_platform.c...
C:\Keil_v5\Nordic_SDK\nRF5_SDK_12.1.0_0d23e2a\components\libraries\util\app_util_platform.c(17): error: #20...
am trying to use SPI with nRF 52832.
So I implemented spi_master.c which was used in nRF 51822.
However, it does not move hard.
The length set by SCLK does not come out...
Hi,
So I'm fairly new to programming the nrf51822 and using the Nordic platform.
I'm currently using the nrf51822 Waveshare DK. I have setup JLink5.1.2, nrf5_MDK_8_5_0...
Hello,
I am using SD 130 on nRF5 with SDK V12.1.0.
I want to write to a characteristic using the android debug app (nrf connect).
This is my code for the characteristic...
Greetings,
As mentioned in this blog post, GCC compiler -flto flag isn't mysteriously present since SDK 9.
devzone.nordicsemi.com/.../
Any specific reason for this...
Hello,
I use a SparkFun programmer to flash a nRF52832, once I flash my board (with the program below), I type in my terminal : "JLinkExe -device nRF52 -speed 4000 -if SWD...
I have many peripherals, dealing with each of them individually will be very ineffective. The peripheral has no buttons, but it has a display.
Questions :
For security...
Hi,
In my application of interfacing SD card with nrf52, I am using SAADC to sample the input signal at 1000 samples per seconds. These samples I am combining in 84 packets...
