Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I see a number of threads on the Nordic devzone where people are asking about official support for a DFU bootloader that combines BLE and UART for transports. Most...
hello Nordic
i am working with nrf52840, SDK16.0, s140 (maybe i will change softdevice later)
i build a project on the peripheral blinky example, i change the advertising...
Hello,
My application is based on the example "ble_thread_dyn_mtd_coap_cli" (nRF5_SDK_for_Thread_and_Zigbee_v4.1.0). I would like to be able to send large files via Bluetooth...
Setup -
nRF52840-DK
Nordic Connect SDK version 1.5.0
Sample - nrf/samples/peripheral/lpuart
Commented out "uart0" in the board specific overlay
Uncommented console...
Hello i'm trying to compilate the project secure_bootloader_ble_s132 but i'm having issue with micro-ecc.
when i complie on keil the bootloader exemple i get this error...
Hello,
As the question shows, how to add RTC function to a 5340 empty project?
condition
ncs:1.5.0
board: nrf5340dk
I have found a project,but it's 52840.
...
Hello,
My application runs in non-secure mode on the nRF9160, and I would like to disable external access to CPU, RAM and Flash.
I understand this is done by setting the...
Hello
I have board nRF52833 and i have several questions:
1. Is AoA example available ? I would prefer to have example of software for tag and for the localization...
On a custom board based on nrf52840.
We want to implement OTA DFU with radio (not necessarily BLE, e.g Serial 4G Modem)
We already checked the Serial DFU example and made...
Hi
I found the function
in nrf_ble_scan.c.
This decoding looks wrong to me since https://devzone.nordicsemi.com/f/nordic-q-a/27012/how-to-distinguish-between-random...
my gcc version: gcc-arm-none-eabi-9-2019-q4-major
defined in discarded section `.intList' of app/libapp.a(softuarte.cpp.obj)
////////////////////////////////////because...
Hi,
Is it at all possible to use the QSPI interface of nRF5340 to interface a micro SD card? Is sending custom instructions combined with long frames, as suggested here...
Hey Nordic team,
We have ECG/EGM alignment problem over BLE, the peer ble chip use RSL15, they came up with the below algorithm, which do need an API to get connection...
