Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
There's a Bluetooth mesh sensor server, which realize, for example:
present ambient temperature property and
desired ambient temperature property.
A Bluetooth mesh...
Good morning,
I'm trying to port the HTS to the PCA0056 board towards chip nRF52833.
I followed the guideline and modified memory mapping as follows:
Section Placement...
Hi.
I'm currently trying to scan non-connectable advertisement for continuously.
So, I'm going to set the value of scan window and scan interval same.
For that purpose...
I wants to use break point in project but when i set break point then 4 or 5 times working after that goes to NRF_BREAKPOINT_COND, I am using nRF52832. so guide me where is...
Hi,
I am trying to setup the serial UART DFU process for a custom board. I am able to build and program a combined firmware hex file which includes - Softdevice S140 ...
Hi guys
I have a project that needs to use multiple 1.8V sensors and transmit data to the mobile phone through Bluetooth. If NRF52832 also uses 1.8V power supply, it can...
Hi Everybody,
I have obtained a free personal Segger Embedded Studio license to use on a nRF52 evaluation board and started to write and debug code.
When I port my code...
Hi,
I use the latest connect sdk 1.4.0 and modem firmware 1.2.2. If I load the default aws_iot code it does not subscribe to the topics set in "topics_list" in the code...
I am using SES Nordic Edition 4.52 and I am building a Zephyr project configured with nRF Connect SDK. After the initial build completes, every time I build without cleaning...
I have a device using the nRF51822 chip on which I was successfully using the BLE sniffer V3.0.0 PCA10028 firmware. The latest V3.1.0 PCA10028 firmware does not work but I...
I am trying to download version 8.31.1 of the nRF device firmware pack for keil from this link
developer.nordicsemi.com/.../NordicSemiconductor.nRF_DeviceFamilyPack.8.32...
Hi.
I'm trying to integrate the MPU9250 with nRF52832 using i2c (TWI) on my nRF52-DK
I have found various libraries but none of them are working on my hardware. All of...
After several record updates one by one I get FDS_ERR_NO_SPACE_IN_QUEUES. However after each record update I wait for FDS_EVT_UPDATE event. I was sure that waiting for this...
I have %XRFTEST working on the 9160 in every band listed in the datasheet other than Band 14 and 17. Is there a reason these bands are not supported with the test mode?
...
I'm looking into integrating the SoftDevice controller (not full SoftDevice) from nrfxlib into NuttX RTOS. NuttX would already provide the host layer so I would only need...
