Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi all,
We are testing with the nrf9151 (mfw 202) on custom hardware with an external active antenna (molex 206640) and a slightly altered SLM (from SDK 2.7.0). Most important...
Hi,
I'm developing firmware for the nRF52840 DK using nRF Connect SDK v2.9.2 , and I’m running into a problem that didn’t occur in v2.8.0 .
My project uses Zephyr and...
Hi,
I am working with the NRF52832 SoC using the NRF52 DK and developing with NRF Connect SDK version 2.7.0. I have enabled BLE with LBS, BAS, and FUOTA services, along...
I have a requirement where I'm using a .NET-based test adapter that communicates using the Modbus protocol over a serial (COM) port.
Now, I want to develop a BLE Central...
I want to use gpiote and functions like:
- nrfx_gpiote_input_configure
- nrfx_gpiote_in_event_enable
This is added to the top of my document:
#include <nrfx_gpiote...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi Nordic team,
I’m working with the nRF5340 using the Bluetooth: NUS (Nordic UART Service) example from the Zephyr SDK . Since this example primarily uses the UART peripheral...
Hello,
We upgraded our project to nrf connect sdk v3.0.2 from v2.9.0 and can no longer use pin 0.00 and pin 0.01 as gpio. The problem seems to be in the nrf53 soc.c file...
Use API: k_thread_state_str() to get the status of the thread, but I don't know the length and content of the obtained string. I want to understand this part.I want to query...
Hi,the Nordic team
I am developing Matter over Thread on nrf54l15, this device is a SED battery powered device, how can I measure the remaining battery power?
Hi,
I want to add scheduler server to the mesh/light sample with nrf52DK, I change the element define like below:
static struct bt_mesh_elem elements [] = {
BT_MESH_ELEM...
Dear Nordic Support Team How are you? Currently we are looking into how to configure, compile and run a full-fledged NRF5340 project which should provide us with:
- Latest...
I am looking for recommendations on whether to use the 'nrfx_wdt_*' component module or the 'nrf_drv_wdt_*' component module when adding a hardware watchdog to my product...
Dear Technical Support Team,
I am trying to integrate and run TensorFlow Lite Micro on the nRF5340 Development Kit using the nRF Connect SDK. I have tested both SDK version...
