Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I am using nrf52840 DK (pca10056) board and nrf5SDK 16. There is one low power sensor connected to the board via SPI interface. My program consume less than 30uA before I...
HI:
I transfer the init packet and firmware to bootloader successfully by UART DFU, and then the app can not start. It report error as below:
<00> info> app: Inside main...
Hi All,
My update of nRF Connect v3.3.0 failed after a while:
Update of nRF Connect failed with the following Error-MSG:
On the same day I got an install from Oracle...
Hello everyone,
I would like to use the PPK with a NRF52 Dk, but I have external sensors connected to the VDD and 5V, so when I will plug the ppk I will have to disconnect...
Hi,
I am reading a 24-bit data from SPI by getting a data-ready interrupt from GPIOTE pin in a NRF52832 chip. I have to buffer data for the BLE interval duration then send...
Hi,
I am using BLE-UART example in my project and to start advertising I am using below piece of code.
By default in the sdk (ble_advertising.c) the advertising type...
Hi,
I don't want the spm and application firmware built together so I tried using the "spm" sample in version 1.3 of the sdk. However when configuring the project i t...
I have a requirement that my peripheral device should only rely on the central to start any security operation. Right now I see a problem when the central side removes the...
I am new to BLE with my nRF51. I've got this example and I try to stop a RSSI scan when the device get all advertising data from the local device.
But when I try to add...
I burned this program in nrf9160 ncs v1.3, and how do I fix the following error?
An example can be found in the figure below
Example prj configuration see figure ...
Hi,
I would like to evaluate the NRF52811 chipset module (BMD-360 from UBlox) using the NRF52840 DK.
If I am to read the Constant Tone Extension that will be transmitted...
I followed an instructions developer.nordicsemi.com/.../gs_assistant.html in the case of Kubuntu 20.04 and developer.nordicsemi.com/.../gs_assistant.html in the case of Windows...
Note: This is related to the following issues:
- https://devzone.nordicsemi.com/f/nordic-q-a/63255/nrf9160-getting-stuck-after-cell-change
- https://devzone.nordicsemi...
I have been running some of the examples and have noticed none of the logging ever works on the Debug Terminal. I am using SES with Nordic SDK 17. When I run any of the SDK...
Hi,
I am using sdk for mesh 1.0.0v and have been running some tests on the mesh network. I have been getting an error within the function net_state_seqnum_alloc() , which...
