Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
I want to use this sample application, to connect with nRF52832 DK loaded with Running Speed and Cadence Application. In other words I want to use nRF9160 as a gateway for...
Hello all,
my compiler can't find the definition to timer functions : nrf_drv_timer_init(), nrf_drv_timer_extended_compare() and nrf_drv_timer_enable(). bellow my code :...
I am using Nordic nRF52832 Development kit . I want to interface Load Cell with the Development kit. Which examples in SDK i should refer to get started with Load Measurement...
Hello ,
i am facing some issues regarding nrf mesh uart example.i am using nrf52 sdk and trying to use uart for my project to send a data to a particular node in a group...
Hello All,
I am trying to merge the "secure_bootloader_s132" and "ble_proximity" examples.
I have combined all file .
(Here i am using Segger embedded studio with nRF52...
Based on the mesh sdk3.1 operation dfu, according to the operation instructions, dfu_mesh.zip cannot be generated.
nrfutil dfu genpkg --hlep Found no parameters for mesh...
Hello everyone,
A nRF52832 with SDK 15.0 was used for my application. I am trying to send a large amount of data via BLE with a custom BLE service. I extended MTU size so...
Hi
I have been developing a 'custom' firmware to be used in a nrf52 based device. The idea is to replace the original firmaware (too limited) and burn my own.
Hence, I...
FYI,
the auto-update fails for version 2.7.0 of 'nRF Connect for Desktop’ with the attached error dialog.
I had to manually download it again from the link below, and...
When I am trying to run my code in nrf52840 DK board, the program halts in a specific PC and does not go forward (2nd image).
I am using SDK version 14.0.0 and softdevice...
i opened the example of ble_app_uart_c in \examples\ble_central\ble_app_uart_c\pca10056\s140\arm5_no_packs in <nRF5_SDK_for_Thread_and_Zigbee_v3.1.0>
and i haven't changed...
Hi!
I have been following this process to develop using armgcc and Eclipse: https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/development-with-gcc-and-eclipse...
everyone, i have a problem whit 51822. nRF5_SDK_12.3.0_d7731ad
i measure time from 51822 poweron to main .
if i only softdevice and app code, time is only 4-5ms only....
Hi,
I have a question about parent.
Firstly, make topogoy as belows.
ZC --- ZR --- ZED
In this situation ZED's parent is ZR. correct ?
Let ZED's ERASE_PERSISTENT_CONFIG...
Hi,
When I run the flash_fstorage sample program via nRF5_SDK_15.3.0_59ac345, I get output that suggests all has gone well:
fstorage example started.
SoftDevice not present...
