I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
We have bought one nRF52 DK and one nRF9160 DK with proper programming (the nRF9160 is able to connect to the cloud via cellular network), but the two devices are not able...
Hi, I am an internship student and so new at programming. I have a nRF51822 DK that includes;
2 x nRF51822 module
2 x BLE master dongle
J-Link Cortex emulator (Debugger...
Dear all,
I am trying to program a chip using an st-link v2 connector.
The chip is nrf52832.
Although I am able to upload hex files that come with the SDK examples...
Hello, I am using a nrf52832 Soc for my development. I follow this https://github.com/bjornspockeli/custom_ble_service_example for the custom BLE service. I can do a specific...
Hi,
I am using nRF52840 Preview-DK with SDK v15.3.0
I am using the serial library to write to UART 1, while writing all goes well while I write less than 255 bytes...
Hi,
In the nus example of sdk 15 the device does not advertise if i comment out the uart_init() function. Why does this happen?
What is the relationship between the uart_init...
Hi guys,
After i provision for client node or server node by smartphone i have unicast address for server model or client model. How can i send message from client to server...
Ubuntu 19.04
SDK 15.3
nRF Connect v2.7.0
Nordic_HTS example both pre-compiled and self-compiled
Uploading to Fanstel BT832F and nRF52 DK
When I upload the example...
Hello,
My goal is to send a binary file by Bluetooth into the nRF52940 board from the terminal. I saw the ble_app_uart example. It seems to be exactly what I want to do...
Hello,
I need to use USB 2.0 connection as a USB MSC device as well have it communicate over a USB 2.0 connection to a Wi-Fi module.
I know there is a USB 2.0 built into...
I'm working on a project using nRF9160 DK.
How can you use MQTT+TLS in nRF9160?
Where should ca certificate file be stored?
I modified the code below in mqtt_simple...
hello i am using nrf52832 DK and working UART_APP_BLE , i want know where the data will be stored when we send any message through mobile to the device. can we see the received...
Hi, I am new at programming.
I am trying to program nRF51822 DK. But My Desktop can't appear J-Link Debugger as a USB drive.
I read some posts about that but I didn't...
Hi .......Clan
I am planning to make chatbox mean chatting (transferring the messages) between the central and peripherals even peripheral to peripheral , and device peripheral...
