Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
HelloI am trying to program nRF52832 QFAA and am succeeding only partially: the debugger is connecting to the chip, and I can RUN step by step, however, I'm seeing only the...
Hello, I have adjusted the Uart Central Example from the SDK 15.1.0 with the stack s140 v6.1.0 so that the device can connect to two peripherals. The name of the device is...
Hi All,
I use SDK 15.2 to periodically trigger ADC acquisition tasks via PPI. But SOFTDEVICE: INVALID MEMORY ACCESS error occurred while the system is running.
I found...
I am using nrf52832, SDK v14.2, Softdevice s132_nrf52_5.0.0.
I had program the softdeive in flash, and I program the DTM firmware as application(start address set as 0x23000...
Hi Guys,
How do I configure Embedded Studio to generate full build log output? For example I want check whether all the header I included is compiled correctly.
Please refer back to the original link
The reason for this massive edit is because this post included code I tried to reconstruct from memory at home with only the SDK sources...
Dear team, We are getting an error in running the Android app in the background: ' Service destroyed '. It comes when the app is minimized and use any other app after that...
Please update the excellent guide at https://devzone.nordicsemi.com/b/blog/posts/getting-started-with-nordics-secure-dfu-bootloader for bond forwarding.
Among other happy...
Hi,
I wish to use AES ECB based on M52840. I use ble_app_uart example as template.
I enabled NRF_CRYPTO_ENABLED, NRF_CRYPTO_BACKEND_CC310_ENABLED and NRF_CRYPTO_BACKEND_CC310_AES_ECB_ENABLED...
Hi,
i am totally beginner to the nrf ,i couldn't able to understand the TWI sensor program
where i will find the API , funtion definition
i want to understand each and...
Hello,
I was trying to implement the proxy profile into the Enocean switch example to try if the friend node for the switch can be provisioned using the Mobile App. I encountered...
hi sir
i have start my project in nrf52832 and i have some Analise BLE RSSI V Meter chart .
and pls give me help hoe to smooth my RSSI value in my chart ............ ...
Hello,
I red a Reference manual v3.0 for NRF51, chapter 31.1.3 (Input impedance).
And I did not understand information about impedance.
What maximal input resistance can...
Hi,
I would like to establish UART communication between nrf52 DK & other microcontroller. I checked the uart example (peripheral folder) in SDK 15. I was not able to flash...
Hi,
I just recently got into designing Bluetooth devices and I am experimenting with NRF51822 and BLE400 board. I managed to compile and upload the examples from SDK 11...