Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
I've come across a couple of products that shows up as both classic and BLE. But when connecting to these products via nRF Connect or inspecting the traffic, I can't seem...
From reading the reference manual, product specification as well as searching the developer zone: here and here . Is it correct that the AVDD pin supply's ONLY the radio....
I have a strange problem with the secure bootloader.
After a succsessful DFU update of firmware, the firmware starts, but resets after a short while (about a second). ...
Hi,
While I'm Flashing LED Blinking Example in nRF51822 Ek using Keil uVision 5 along with SDK v12.2.0 , Program is uploaded but LED is Continuously glowing without blinking...
Hi
I have been trying to make a dual bank serial dfu bootloader with security features for nrf51822 (board 10028), but seems the UART/HCI dfu support is missing in SDK...
Hi,
I am having some trouble getting my design into low power.
I have a BLE central application using an nRF51822. I am using the power on sleep mode by calling sd_app_evt_wait...
Hi Nordic,
I have an application that perfectly runs in the nrf51DK but that does not work in my custom board. In my custom board everything else works (i2c, leds lighting...
I have a nRF51822 development dongle. I followed by the instruction and installed the USB friver, nRFGo Studio and Wireshark. All these software are installed a Win7(64bit...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
What is the best way to go about implementing secure reads/writes to the NRF52 NFC tag? I noticed there didn't seem to be any built in security functionality in those areas...
I am attempting to use nrf_drv_adc.h in a project where I am splitting up my methods across many C files and, to my surprise, nrf_drv_adc.h does not have any include guards...
Hello,
I received the above error using NRF5 SDK 12.2. I have modified "nrf_drv_config.h" so that it reads #define TWI0_ENABLED 1 . Also, I put #include "nrf_drv_config...
Using nrf52 DK , SDK 12.2 , and armgcc.
I want to use BLE_UART but I also want to bond.
I started with the BLE_UART example code and added peer manager and FDS.
I...
I've been trying to track down a bug where a couple of my Central test devices, a Nexus 5 and 7 (Android 6.1), won't send a connection request to a peripheral they're bonded...
