We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Seeing the failure below and wondering a couple things:
How did the device get into this state?
How do I disable AP protection? The Kconfig GUI seems to indicate that...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hi There, i am pretty new to this ble and arm world. i was exploring my nrf52dk with sdk15 cryptography libraries. I have looked into an example of Elliptic Curve Diffie-Hellman...
Hi,
I had done secure OTA in my custom board using SDK12.2.0 with S130 v2.0.1 softdevice. But when i am trying to update the same for multiple times then its not happened...
Hi!
I'm running UART example and modified to run upon interrupt and its working fine, but in main() if condition ( if (cr == 'q' || cr == 'Q') ) is not executing even condition...
Hi,
I'm trying to toggle GPIOs 32-35 but it can't be done. Other GPIOs though such as 15,21,30 I change successfully.
Here's my code:
I saw a solution regarding NFC...
Until lately, I have never used characteristics longer than the 20 Bytes and if the length of application data was longer, I would fragment it on the application layer.
...
Hi there,
I’m trying to port Thingy to Segger Embedded Studio. After reviewing some related blogs on devzone and github, I have imported the Keil project into SES. All files...
Hi,
I'm trying to use adxl335 accelerometer to detect motion.
I'm having trouble understanding what the output of the accelerometer means.
Obviously, it should tell...
On SDK 12.0.0, SDK 12.1.0 and SDK 12.2.0 only
Please Do not judge the quality of SDK based on number of entries here. This thread should be considered as part of Nordic...
On SDK 13.x.0 only
Please Do not judge the quality of SDK based on number of entries here. This thread should be considered as part of Nordic effort to find issues and...
The soc_evt_handler() function in nrf_drv_clock.c need to set m_clock_cb.hfclk_on = true.
When the softdevice is enabled and multiple modules request the HFCLK using nrf_drv_clock_hfclk_request...
I'm following your instructions for testing the Thread Secure DFU example , but I run into a message "Waiting for NCP to promote to a router ..." at step 6 and I don't o bserve...
I had used the examples\peripheral\blinky\pca10040\blank\arm5_no_packs Keil project from nRF-SDK v15.0.0 using Keil MDK v5.25.
EDIT: as described here: http://infocenter...
Hello,
I am currently implementing an OOK modulation with the nRF52 -DK and therefore I need to start the radio with a carrier on defined frequency. Obviously there is a...
Hello
My English is not very good and please point out if my problem description is not clear. I am building a central project that can connect two peripherals. The template...
Hello Nordic,
we are going to perform RF-PHY test for nRF52810 at DEKRA. Can you help us with IXIT filling? There is one answer available at devzone:
https://devzone.nordicsemi...