I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
HI all:
If the iphone saved is English name i can parse it out, But if the save is a Chinese name I don't know what is to use the utf-8 encoding and unicode, who has successfully...
Hi，
i defined spis rx and tx buffer length at:
#define HUB_SPIS_RECV_BUFF_SIZE 1024
#define HUB_SPIS_SEND_BUFF_SIZE 1024
because the rx data length will be vary...
Hello nordic
I use ble to create custom services, I want to create an embedded system that can create and send and receive data. I am using sdk version 14.2.0 and what...
Hi,
Im currently designing a custom pcb using nrf52 reference design available here . In my design, I have to connect the ground of two analog signals to VSS of nrf52832...
I tried Blinky blank application on PCA10040 by IAR. By pressing "Download and debug", everything is fine, I added RTT debugging information and can see it from RTT viewer...
I Have an issue trying to flash a nrf52832 custom board.
Something extrange happens because when I download an example from keil that blink a led(gpiote_pca1036(nrf52 PCA10036...
We are using s110_nrf51_8.0.0_softdevice.hex soft device and nRF51 SDK v10.0. We have below questions in case of soft device assert scenario.
In what scenario's soft...
Hello,
I am working with the example of PDM example on the nRF52832.
And over this I would like to use the drv_speaker. I put all the files from the Thingy 52 example...
On a system using an NRF52832 with S132 softdevice (without no external LFCLK XTAL), in low power mode via sd_app_evt_wait() - we see a nominal current of ~3uA with a periodic...
Hello Nordic,
Can you share pdf of nRF91 sneak peek presentation.There is an audio problem on video.
Best regards,
Marcio
www.nordicsemi.com/.../Low-power-cellular-IoT...
hi team,
i am having a doubt. i had created a service for connection interval which is 0x1528. with read and write properties. in that we can set value from 100ms to 10240ms...
I would like to ask for any information regarding the near-future plan for the nRF SDK for Mesh.
Are these features planned? And if so, when would they be implemented?...
nRF52832
There are three ways of working with the clock registers, a hardware access layer macro set, the nrf_drv_clock.c/h, and direct register access.
What is the...
I am implementing Device Firmware Update using BGLib on C# using BLED112. When i am writing on the DFU Data point on Peripheral (which is a Nordic's nrf51 chipset), i need...
hi,everyone.
version:sdk10.0
i know the nrf51822 system running order is: softdevice->bootloader->app.But i have a question when i am reading bootloader. If the program...
