I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I have downloaded the Eddystone example to my nRF52832 dev-kit and I am trying to register it with the google beacon platform using their beacons Tools app but it says that...
Hi,
i have the below queries:
In our project we are using multiple masters and multiple slaves, in that each slave is dedicated to a single master.
for ex: we are having...
Hello. I created some HID device based ble_app_hrs_pairing_nfc example on NRF52. And I have a questions:
1.I need to automatically reconnect to bonded device after reboot...
By default, the NRF_DEBUG is disabled. After enabling, and removing this assert check:
devzone.nordicsemi.com/.../
I am now hitting another one here:
#if ( configUSE_TICKLESS_IDLE...
Reading the documentation online for the BPROT component for the nRF52832, it seems like resetting is the way to clear the Write Protection bits in BPROT. Is resetting the...
I'd like to be able to change the ble connection interval during during runtime to save power. I followed this post and found that p_ble_evt->evt.gap_evt.params.connected...
Hi,
We like to develop a battery powered device with small current consumption which will communicate with mobile devices over BLE. It will comunicate with mobile device...
Hello Everyone,
It is unclear to me how a soft-device operates regarding multi-tasking and event-handling. I'm assuming Nordic engineers have their own real-time operating...
Hello, i wanted to ask if NRF51 Dongle NRF51-Dongle is capable of sniffing packets from NRF52xx parts? If yes, what are the limitations, because i think that nrf52xx parts...
Below linked blogpost says,
if using a PCB antenna, the matching network should consist of one shunt component.
devzone.nordicsemi.com/.../ .
And in the reference design...
Greetings,
For my application,I need to change the nrf51's mac address.
Previously I have changed the MAC id using the following code,
static ble_gap_addr_t m_central_addr;...
Hello friends,
i am new to embedded programming and trying to learn the new things in embedded for this i am doing 1 project in which i am using mpu9250 with pwm.
is...
Hi,
I want to interface FN-M16P with nRF52 through UART. To access this module I need to send commands to perform specific actions.Is there any specific example like this...
Hello,
I am new in this community and I am trying to get started with developments using nRF52840 DK. I am using SDK 13.0 for the library and I compile my code using armgcc...
