Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
I use a Peer Manager in my project (nrf52832, SDK13.1).
Peer manager use FDS, but i also want to use FDS for storing user data.
As i know , FDS module use 1 virtural page...
Hi all,
I have here NRF51-DK, I am a bit familiar with the kit for a while.
Now I want to make a system using NRF518422 chip.
I manage to find a module - "Taiyo Yuden EYAGJNZXX...
I'm starting to read all the resources and examples included in the SDK. However, there doesn't seem to be a lot of emphasis on explaining how the programming architecture...
Hello,
I have the following observation regarding the potential problem with DFU bootloader
implementation :
I have noticed that the Bootloader DFU implementation (nRF5_SDK_13...
Hello!
I would like to program the nRF52 using the JLink Commander and protect it afterwards. Which register do I need to manipulate?
Thanks and kind regards,
Mi...
I download the nRF Toolbox app and its in swift.
My current app is in objective-C and I want to implement dfu in my app.
Is there any framework that can be used in my...
Hello,
I recently migrated to nrf52 and countering some problems
with NRF_ESB concurrently with BLE.
I started with This example which was a part of the Running micro...
The chip is nrf52832.
The SDK version that I am using is nRF5_SDK_13.1.0_7ca7556,the example that i used is ble_app_uart.
When i debug about low power,i encounter problems...
Hello,
I'm using NRF51-DK (PCA10028) and I want to be sure if I'm using the external 32KHz oscillator (X2).
I'm using SDK12.3.0. I'm running the beacon example.
In...
Hi,
Is there any tutorial already for the version 14.0.0 of the SDK (nRF52, more specifically I am using nRF52832)? I would like to know how to configure Advertising, and...
Hi
I have development kit nrf51 PCA 10028 and try to run uart example example with loopback (RX connected to TX, RTS connected to CTS). Unfortunately, after sending, I...
I'm using the bootloader_secure_ble example from SDK 13 on an nRF52832. I'm using the GCC toolchain. Here is an extract of the linker file from the example:
MEMORY
{
...
I'm running nRFgo Studio on Windows 10.
Have tried to re-install (nrfgostudio_win-32_1.21.0_installer.msi) without success..
Any idea what to do?
Thanks!
I'm using nrf52 with S132. I was trying ble_app_uart example and it is not printing any log messages into the COM. Do I need to do anything extra to make it work?
Hi there,
I am currently wondering if the following is possible?
As stated by the Cortex M4 reference manual states that a system can have 200+ seperate handlers within...
