I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi,
Can you please explain to me what bonding consists of ?
Because i want to use it in DFU from an app. I see an app where we can from the it do DFU . in Fact, the...
Hi there,
Thanks to the great tutorial from Vidar, I can play with the blinky example in Eclipse on Mac. Now I want to try the other examples, and encountered the "Error...
Dear all,
I need to know in detail the nRF51822 RF capabilities asked by bluetooth SIG.
Items 1 to 12 in chapter 1.3
See attached document RF ICS 4 1 0 (002).pdf
Thank...
Hardware: Rigado BMD-200 B using the nRF51822_xxAB
Softdevice: S110_nRF51_8.0.0
Base project: ble_app_hrs_s110_with_dfu_pca10028
Project Device: nRF51922_xxAB
Project...
Hi All,
I am trying to develop a application using radio communication, so i choosed to develop a application so it can able to tx and rx. So i integrated both rx and tx...
Hi All,
We are trying find a way to upgrade nrf51822 in the field post initial release.
I read the following posts
( devzone.nordicsemi.com/.../)
( developer.nordicsemi...
My board requires P0.9 and P0.10 to operate as GPIO pins. On the NRF52 these pins share the function with the NFC antenna. How do I make them function as GPIO pins?
I know...
Hi,
I just finished compiling my code for the nrf51 to take ADC measurements and send the hex values over ble tuart o my iphone. Now I want to see if I can send that data...
Hi, i know maybe this question was asked before, but i have a particulary issue.
I have 2 devices connected through BLE. Just when them get connected i need to send a byte...
Hello!
I need to read a string from UART, there's code below:
unsigned char GetChar(void)
{
while(!RI)
;
RI = 0;
return SBUF;
}
int Readfstr(void)
{
char...
Hardware: Rigado BMD-200 B using the nRF51822_xxAB
Bootloader: dfu_dual_bank_ble_s110_pca10028 with the device set to nRF51822_xxAB
Softdevice: S110_nRF51_8.0.0
DFU Tool...
I'm trying to use BLE library for python to communicate with one Nordic nrf51844 chipset. Because one characteristic is notification enabled, I need to enable notification...
Does there exist a white paper describing some typical PPI use cases with coding examples? The only one I've found is the peripheral/gpiote example and it is severely lacking...
