Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I have a PCA10040.
I downloaded nRF52_SDK_0.9.2_dbc28c9.zip.
I want to use "ble_peripheral\ble_app_uart " sample program.
However, supporting it is PCA10036. (by readme...
I am modifying the ble_central\ble_app_hrs_c example to connect to a peripheral with an "Authentication Characteristic" that is used to initiate the peripheral-specific authentication...
main.c: Warning: C3912W: Option 'device' is deprecated.
main.c: error: C3903U: Argument '-D__EVAL' not permitted for option 'device'.
i am getting error. can you help...
In my application, I would need to use both RTC(function as a timer) and Watchdog(as watchdog). Is it OK?
I saw in the manual "the watchdog will automatically force the 32...
my purpose is to use the 51422 or 52382 as a central role to search my own service, or any other SIG standard services.
DK :nrf51422 ,
version : 9.0.0 and 10.0.0,(i...
I m developping an iOS application, and I need to integrate the DFU part.
I found the IOS-nRF-Toolbox , but what I need is to integrate only the classes that manage the DFU...
The nrf52 with SDK 0.9.2 SDs132_nrf52_2.0.0-4.alpha_softdevice has 3 TX_buffers(2 count can i used).
I think there may be some preserve TX_buffers for BLE central or ANT...
I'm working with nrf51 board, I'm using I2C to communicate with an accelerometer (see the scheme), the communications are successful but I dont see any pull up resistors in...
Hello there, this is my very first post here.
I have a pair of nRF24L01 modules with built-in PCB antenna, I would to know if is possible to obtain the approximated antenna...
I have the nRF UART-over-BLE examples working on nRF8001 & communicating with the corresponding Android App as "host".
Instead of the Android App, I would like to use an...
Hi
I have a problem using TWI driver with my softdevice enabled.
The TWI is able to communicate successfully to the slave without the softdevice.
But the same code...
Now that my application finally supports OTA DFU, I hit a new problem. Instead of nRF51822 starting the newly flashed application, some old version seems to start. Or at least...
Just a general plan not a detail one . like this: in the SD132 2.0.0 we will add the funtion of change the MTU up to about 150 bytes，at the approximate time 2016-4
I am testing the freertos port, based on the hrs example in the new SDK 10.0. I have run into an issue while using the uart during long transmission sequences (where the fifo...
