I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Even immediately after issuing a gc (garbage collect) command, "freeable words" is still 1022:
Why?
What does this number actually mean?
The documentation just says...
I'm hitting a couple of different logging issues with the latest SDK15. In the most recent case it appears std_n is hanging while calling nrf_log_frontend_dequeue.
Attached...
Hello,
We have an application made with SDK 11 on nrf52832 but we want to add mesh SDK. Is it possible to make coexistence with SDK 11 ( we don't want to do the migration...
I have to send packages continuously; How can I get feedback on the success of transmission before sending the next package? Which event should I use? and in what callback...
Hello! I occasionally have a crash during the development of nrf52832 (SDK14.2), but this phenomenon is not very reproducible. All the information about the error that I want...
i am able to read data from the i2c device ,,,but i dont know how to send the data through the bluetooth to a central device. i am using the nrf52832 and sdk 15.0.0..someone...
I am just getting started developing a Mesh network around the nRF52840 .
I am confused about which SDK to use for mesh development. v15.0 or SDK for Mesh 2.1.0?
Thanks...
In the Nordic Connect app, firmware uploads keep running even if the app goes in the background or the device goes to sleep. What should I do to run the DFU library with the...
I'm starting with BLE Mesh SDK and have some doubts about their examples.
What's the difference between Light_Switch Client/Server version and Proxy_Client/Server and Provisioning...
Hello,
First time posting, Here are the details of my setup, I would greatly appreciate any help from anyone at this point. I have purchased 2 nrf52 development kits with...
Dear Sir:
I use ble_app_uart example , i want use pwm to driver the FR Port ,Peripheral load. the Peripheral load is pulled up to battery.
when driver the load ,the...
Hi All;
Just a major concern of mine is that SES IDE is so inconsistent;
I can build a solution get errors and warnings...
Without editing anything and rebuilding the...
I have an issue with my board. It resets occassionally itself. When the board is starting by debugger and when it resets itself I can read 0xD in RESETREAS register. What...
hi,
I tried to provision the light example using the nRF Mesh app.
So far, I succedded in provisionning the device but i couldn't set the publish suscribed addresses,...
Hi, I'm using a modified version of the light_switch example to control a RGB led on Mesh SDK 2.0.1. I already managed to control the led by using 3 variables for each color...
