Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
Hi Nordic team,
This problem bothers me for a very long time. I cannot find the root cause. I used nRF51822 IC. It uses SDK11 with softdevice S130 and bootloader (but I...
Using nRF52 with SD 132 3.0.0.
Peer manager uses fstorage to store information.
I need to be able to specify the address range which fstorage can use.
Is there a configurable...
Hi,
I have problem with both functions sd_ble_gatts_value on central device.
It works on peripheral, because there is my characteristics definition.
Now I have to read...
Hello,
I'm developing a BLE Application where I use the peer manager. My Goal is to use direct advertising after disconnection if a device already has bonded. But every...
I am using the SAADC on the nRF52832, SDK12.2.0, with it set to 12 bits and low power mode. I have enabled five channels which I run blocking nrf_drv_saadc_sample_convert...
Dose this capture from the Nordic Specification means that to read bytes from SPI i need to send before. Each byte i send i get a byte!!!
MLy case i have read only sensor...
I am using the nrf52832 with the s132 for a project in which I have a frame with 24 bytes that need to be transmitted through BLE.
I have followed the tutorials and I have...
Hi,
First I'd like to salute the great work done by you Nordic people for those open source and hardware.
I just installed the SDK 10.0.0, S120, gcc-arm toolchain, configure...
Hello, I'm a beginner with the BLE technology and nRF52 is a good tool to start with it.
Currently, I have a setup that allows a Raspberry Pi and an nRF52 to communicate...
Hi. I have a problem with programming brand new chips nRF51422.
I have connected: Vcc (1, 12, 35, 36), Gnd (33,34,13), Swdio (23) Swdclk (24).
christal on the board:
...
I had downloading many versions SDK,from 10.0.0 to 12.2.0.But when I Program SoftDevice then download the examples,such as the path:
nRF5_SDK_12.0.0_12f24da\examples\ble_central_and_peripheral...
hi,all.
when i first time connect nRF52840PDK to PC, and open nRFgo Studio, but encounter this problem:
no device detected.
screenshot:
I click recover button many...
I want to send several packages in one interval from my iphone to 51822(s130).But the demo ble_app_uart can only receive 1 package per interval（ipone6，lightbule，writewithoutreponse...
I want printf the date and time when compiling code.
But I drag on this error:
SEGGER_RTT_printf("%s %s.\r\n", __DATE__,__TIME__);
compiler says:
It's strange...
Hi engineer,
I found that the SAADC current is increased after the SAADC function opened, then my processing method as below:
1,I close SAADC function after sampling...
