Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi Nordics
https://devzone.nordicsemi.com/f/nordic-q-a/22595/can-not-received-ble_gap_evt_timeout-event-when-connect-timeout/88877#88877
Referring to the above post, I...
Dear,
I am trying to test BLE on the THINGY:91.
Follow the Q&A for "Introduction to Nordic THINGY:91" webinar, Q12 of @ Petter Myhre
I tried with Zephyr HCI UART example...
Hi,
I'm trying to debug my bootloader (I2C specifically) using Ozone. However the CPU only seems to halt when trying to debug the bootloader.
Also setting breakpoints...
I am using proprietary radio between 2 nrf51 devices, by copying from an example see code below.
That works but now I want to have more pairs of devices and I need to have...
Hello,
I have some custom hardware that uses both BLE 4.0 and BLE 5. I am looking for information on if it is possible to use a nRF52840 Dongle to connect to multiple peripheral...
Hi ! I am trying to design a custom board for nRF52840. I used the nRF52840 dongle's HW files in Altium to create a new board. Unfortunately the Altium project does not include...
I am trying to make the timer example works under the BLE blinky example. I have copy the code and enable the defines in sdk_config,from one project to the other but timer...
Hi i want to send a string using uart over bluetooth. For a try i compile ble_app_uart and flash it to my dk but i can not see the message on the terminal neither in Putty...
Hello everyone,
I am using nrf52832 module with SDK v14.2 and SD v5.0.0 for my development.
Recently, i started facing the below issue:
Once i try to pair the module...
Hi Great QA team:
Our client has made their product in MP stage but found out that some of the ICs with FDS Bug (Base on SDK 15.2):
REF: FDS - data corruption https:/...
Hello,
Quick question.. we are working on a board and running very low on GPIO pins. It would be helpful to remove the low-frequency (32k) XTAL, to recover those pins. The...
Dear,
I am testing with thing91
todo: read and send the temperature to my webserver in each 15mn
using: thingy91, LTE_M
sample1: in the fridge (4C)
sample2: in...
Dear community,
I am developing a firmware using SDK 16.0.0 which handles interruptions from an accelerometer and a timer.
I've built on top of APP_UART lib a set of functions...
Hello,
I tried to use use pc-ble-driver for Ublox NINA B3 EVK which has nRF524840 .
It failed with following error:
./heart_rate_monitor_v6 /dev/ttyACM0 Serial port...
