After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I have ASUS ZenPad 10 with Android 5.0.2,
BLE device on nRF51, S110 SDK9 with fixed passkey and encrypted characteristics with following settings
#define SEC_PARAM_BOND...
Looking for someone that has previous experience building multi protocol / time slot topologies using a mix of BLE (central+peripheral) & custom Gazell connections running...
Hi.
I have nRF51422 borad and want to flash to nRF51422 with JLink.
I supplied to 3.3V power to board and is connedted SWDIO to p23, SWDCLK to p24. JLink is connected...
IUsing the Master Control Panel application on my Android device to connect to my nRF51822 module (acting as the GATT server), I have implemented the Device Manager (v10 SDK...
I have successfully compiled BLE application using tutorials provided on nordic website.
but when I start doing debugging for better understanding find out that I can not...
Am trying to setup a module where I need to send the Serial port ( say from printer/peripheral COM)
to a BLE Peripheral/Central Module. Not sure which SOC or combination...
I have a board built which is a tracking device with a GPS and GSM modem. I'm beginning field testing and have been flashing it with a Segger then disconnecting the Segger...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
I have used the nrf8002 chip before and love it but now I am trying a different application that requires a bit more smarts. I am trying to design a system that can have an...
I have an nRF51822 board that is running fine for a while. At some point, it runs into an error and calls ble_debug_assert_handler() and goes into an infinite loop. At that...
Hi all,
I am new to nRF51822,now I want to used a simple ble application to send a data,and nRF51822 ble device read this data to control RC servo motor ,for example app...
We are using S130 v0.9 stack,
and when BLE device A is connected as peripheral of iphone
and central of BLE device B at the same time
iPhone --> A ---> B
Device...
Hello,
I am working with the nRF DK trying to read a sensor over I2C. I wrote some code in Keil uVision and I finally could read the sensor. The problem now is, for some...
I encountered a strange problem system reset. My application runs on iOS or android. My device was connected by iPhone 6 plus(128G) with iOS 8.1.2. ANCS was turned on. I have...
Hello Everyone
I want to implement TWI interface in my project.Presently I am using Keil UV5 IDE, PCA10028 Development board and s110 7.1.0 softdevice, along with that...
Hi,
So am new to all this BLE stuff, I have been using the nRF24L01 modules but want to move to the BLE variant, nRF51822.
I am these days figuring out the toolchain...
Hi,
I am developing on a nrf51822 based board using s110 softdevice v. 6.0.0.
In my program I need to change the bluetooth GAP device name in runtime
during connection...
Hi,
I compiled the nrf_heart_rate_collector. Apparently, this program only works once, between each run, "remote device" and USB dongle has to be resetted (unplugged from...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi ,
I am trying to set up event using GPIOTE. I want to implement reading of sensor data and sending over BLE when an interrupt is generated due to activity on a particular...
