Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
My custom nRF52840 board uses the STmicro STM6601 push-button controller. To keep the nRF powered, the PSHOLD line must be kept high. I have a GPIO set as an output for that...
Hi there,
I am trying the test the robustness of a BLE use-case. This means that i have to create error scenarios and further observe and analyze how it's possible to recover...
Dear all i have a very funny situaton.
I can only send 1 byte in my service data when I increase it to two bytes it doesn't send. and says invalid parameters
When...
In the right process，like this：
but my program is ：
i lost “Sent Read By Group Type Request, GATT Primary Service Declaration, Handles: 0x0001..0xffff” .
in the...
Please kindly help to push this emergent issue!!!
We detected CLK signal using oscilloscope as picture below:
We can see that clock frequency is set to...
I have been making good use of the Power Profiler Kit with some impressive results on my nRF52 project.
I would now like to extend the testing to view an application where...
Hi
I have some question about DFU for Mesh3.10.
1.How to update Softdevice or Bootloader?such as I'm going to update SD from version 6.0.0 to 6.1.0.
2.Because my firmware...
I am trying to port pc-ble-driver-py to soft device version 6.1. I have made changes to python code to take care of changed API signatures, new constants etc.
When testing...
Hi,
I am using nrf52832, in the ble_app_uart_c example, i want to use rc source as a lfclk,
i changed the following parameters in the sdk_config.h:
NRFX_CLOCK_CONFIG_LF_SRC...
Hello,
I have developed a custom PCB using nRF52832. It's meant to work as an ibeacon currently and consequently works in a non-connectable, advertising only mode. I will...
Hi,
I am trying to use GPIOTE_PIN_HANDLER in the master nrf52. What is the correct way to read data from slave?
Slave device is sending data using nrfx_twis_tx_prepare...
Hi,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I am using app_timer_create() to create low power...
Good morning developers, I want to ask you what is the maximum transfer speed (Kbps) achieved between the chip nrf52840 (peripheral) and a smartphone (central). If anyone...
As I reviewed other post, there are many similar topic.
Thus, I would like to know whether there is new tool for the application recently.
Does Nordic have development...
