I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
In the nRF5 SKD alpha, gatts_cache_manager.c:123 looks like this:
gscm_evt.params.sc_state_stored.state = &peer_data.p_service_changed_pending;
Is this supposed to...
Hi all,
Refer as the antenna whitepaper, The Zs = 50 Ohm pi network need to match. I saw a matched pass filter optimized for nrf52832 from Johanson (Part Number:2450FM07A0029...
i have app_ble_uart and i wan get temperatura with my phone main.c terminal there is my code but i dont had any msg from my BLE controller.But if i changed call of function...
Hi, iOS caches services and characteristics when bonded with device, so we need to inform him to invalidate this information via Service Changed characteristic, but how it...
So I switched from Bluemod+S (nRF51822) to Bluemod+S42 (nRF52832) on my custom board and am trying to adapt my existing code to work on the newer model. Apart from various...
Hello,
can anybody tell me the exact differences between a Link Layer Acknowledgement and the Acknowledgement used by a write Request?
Does anybody have some statistics...
I am trying to implement the Current Time Service in my project and had a few questions:
-The example requires that security be established before services can be discovered...
hai
i am using mbed to program my nrf51822. in my application i need to read two analog sensor values.
i am using p5 and p6 pin for that.
AnalogIn analog_pin_1(p5);...
Can somebody explain what 0xA1 means in this raw L2CAP layer:
0a, 00, 4d, 00, A1, 01, 00, 00, 08, 00, 00, 00, 00, 00
I know 0a, total bytes, and 4d is channel ID, I...
Hello
I was wondering whether is possible to use an updated version of the softDevice into an older SDK, my current hw is a nRF52832pca10040 DK
For example, I am currently...
Hi,
I am using experimental_ble_app_blinky example. In that NRF_LOG over UART was implemented.
I Added some UART code for my use. But after flashing code was not working...
I am using SDK14 and SD132 V5 on nrf52382. I tested the hids_mouse example and it autoconnected without any issues to the phone. In my application, I have 2 modes. Config...
Hi,
We're designing a product with the nRF52 (SoftDevice S132 v5.0.0 production) and an external WiFi module, and are attempting to do a "poor man's WiFi Co-Existence"...
I am struggling to figure out the correct IRAM/IROM settings in keil for the ble_app_beacon example in sdk 14.0.
I am currently using this example on an nrf52 DK and will...
