I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
I would like to know the files contained in nRF5x_MDK_8_9_0_IAR.msi
as well as other files needed for a minimal application.
I would like to know exactly which are those...
Hello iam using softdevice 110 and SDK 10.0.0, i want to know the way to avoid bonding of device more then once, or deleting the bonding information from persistent memory...
I need to change the flag of the scanrsp. I use the advertising_init() and i try to do like this:
scanrsp.flags = FLAG;
but the function ble_advdata_set(&advdata,&scanrsp...
Hi,
I'm tring to generate private key of dfu, but it didn't work fine.The following is my steps.Did I miss something?
C:\Users\Administrator>cd C:\Program Files\Nordic...
I'm trying to tune a chip antenna for nrf52832. I am not an RF engineer but have figured out how to get the basic VNA measurements done.
I've been fighting with finding caps...
Are there any dirty hacks to pass a little data, like 1 bit even, during pairing?
I need my central to tell the peripheral orientation, left/right, as early as possible....
I am using an nRF52832 PCA10040 board, using s132_nrf52_2.0.0_softdevice.hex, and have AIN0 connected to a potentiometer similar to this . The power input pin is connected...
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Hello,
So — in just trying to get the blink example working, I've come across all kinds of toolchain weirdness. I'm using CrossWorks, because it's on OSX and it's way cheaper...
Hi all
Is possible from softdevice or from program application edit the GAP service? I know this service is mandatory but what about edit the structure which is shown on...
Please give me a professor.
In the nRF 52832 sample project, there is an NRF_LOG_INFO function, is this the ability to output a debug string to the UART?
If so, how can...
I have custom service, where I have declared 2 handles inside BLE Service structure, one for button action and the other for custom battery ADC measurement, each identified...
Hi,
I have seen similar questions to this, but I could not make it work.
I am trying to upload a new code using DFU by means of a smartphone (using nRF Connect) or PC...
Hi. I just noticed this bombshell in the release notes for v13.0.0-1.alpha:
Dropped support for nRF51 Series devices.
Although this is preceded by:
...
Hello ! I am trying to implement a write request but for unknown reason it doesn't transmit back the gatt_status. I have setup the wr_auth = 1. GPIO number 19 si actually...
