Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
I have 6 RGB LED strips and I would like to control them by Raspberry PI. 6 strips with 3 colors each require 18 controllable PWM sources, so I have SN3218 which is exactly...
Hi all,
I'm new to nRF51822 and I'm trying to use the fds system.
However, I always get a NO MEM return code when calling the init method.
Any hint?
Thanks
This is my code，the problem is when cpu executed the __WFI() instruct it should be paused ,this means that NRF_LOG_INFO("wake up\r\n") should not been executed only after...
I am trying to integrate an ADXL345 with my nRF52. I am attempting to implement Bjørn Spockeli's driver which I stumbled upon here: devzone.nordicsemi.com/.../
I am using...
Hi all,
I have an application for nRF52 which works fine using SDK 12.1.0. I am now trying to make it working with 12.2.0 and it hangs.
Apparently inside the function...
My question is somehow connected to hardware side of SPI(M) peripheral implementation.
When using SPIM, I am observing 3 types of situation:
WhenSCK pin is defined...
Hello,
I took this project on about a month ago to do bug fixes within the app. The bugs are fixed but the OTA was not tested for the last 2-3 months. No changes were made...
Hi,
I am working on interfacing SD card with nrf52. I am sampling SAADC at 1000 sps and trying to write over SD card as well as sending over BLE. Both operations are working...
Hi everyone,
I am trying to update my nrf52832 chip with another MCU using UART.
I am using the bootloader example dual_bank_serial_s132 with the s132 SoftDevice.
...
I plan on using the ISP130301 and would like to ask the following:
I would like to start my schematic and layout using the ISP130310 from Insight Sip and would like...
I'm wondering if it can be work as an DFU Controller (where sends zip Distribution Packet) not as an DFU Target.
I'm trying to make Each of the NRF51 Cores to be updated...
I am using the nRF52832 very successfully for an audio application. However, I am observing an undesirable high current state after audio playback is complete.
Here is...
Hello Everyone) Have new unsolved problem. My custom PCB based on nrf52832 SoC has only controller, FXOS8700 accelerometer and MAX30205 health temperature sensor. For communication...
I have been using SDK7.2 on an nrf51822 quite succesfully for a number of projects in the past.
However, for a new project, which is just a simple beacon, no complex IO or...
Trying to keep this as short as possible. I have 3 I2C devices on a bus. A LSM303(accelerometer + magnetometer), a high precision temp sensor, tricolor LED driver TCA6057...
